Henny Penny 500 GAS Leak Test, GAS Pressure, Regulator Setting, GAS Pilot & Burner, Lightingand

Page 19

Model 500/600

2.8GAS LEAK TEST

Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position.

After the piping and fittings have been installed, check for gas leaks.A simple checking method is to turn on the gas and brush all connections with a soap solution. If bubbles occur, it indicates escaping gas. In this event, the piping connection must be redone.

To avoid fire or explosion, never use a lighted match or open flame to test for gas leaks. Ignited gas could result in severe personal injury and/or property damage.

2-9. GAS PRESSURE

The gas pressure regulator on the automatic gas valve

REGULATOR SETTING

is factory set as follows:

 

 

Natural: 3.5 inches water column (0.87 kPa)

 

 

Propane: 10.0 inches water column (2.49 kPa)

 

 

The gas pressure regulator has been set by Henny Penny and

 

 

is not to be adjusted by the user.

2-10. GAS PILOT & BURNER

Lighting Procedure - Solid State Ignition

LIGHTINGAND

1.

The frypot should be cleaned per the instructions in Section 3.

SHUTDOWN

2.

The frypot must be filled to the proper level with shortening.

PROCEDURE

 

 

Refer to Filling orAdding Shortening Section.

 

3.

Turn main power switch to OFF position.

 

4.

Turn the gas valve knob counterclockwise to the OFF position.

 

 

(OFF pointed down)

 

5.

Wait a sufficient length of time (at least 5 minutes) to allow any gas

 

 

which may have accumulated in the burner compartment to escape

Step 4

6.

Turn the gas valve knob clockwise to the ON position.

 

 

(ON pointed down)

1207

2-9

Page 18 Page 20
Image 19
Page 18 Page 20
Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Page Keep appliance area free and clear from combustibles Technical Data for CE Marked Products Table of Contents Table of Contents Pressure Heat Time Pressure FryerProper Care Assistance Model Variations Hazardous Situation WHICH, if not SafetyWhich, if not avoided, could result in death or serious InjuryUnpacking Instructions IntroductionStep Unpacking Instructions Ment. Restraining ties may be used for stabilization Position and install fryer to prevent tipping or moveSelecting the Fryer LocationModel 500/600 GAS Supply Main gas line supply GAS PipingHenny Penny Part No , which complies with GAS Piping GAS Pressure Regulator SettingProcedure GAS Leak TestShutdown Procedure ProcedureElectrical Requirements Electric Fryer Data Table Supply Wiring and Fusing for Electric FryerRequirements ElectricalGAS Fryer Motor Bearings Operational Checks Checking the Filter PumpPage Refer to Figure Description Function Operating ControlsControl Panel Operating ControlsSteam will Result Operating ComponentsDescription Function Do not Pull this RING. Severe Burns fromResult in the fryer building too much pressure. Severe Failure to clean the deadweight assembly daily couldInjuries and burns could result Exhaust and Severe Burns will Result Is Under PRESSURE. HOT Shortening willGas Electric Operating Controls Operating ComponentsGAS Model Operating Controls Filling or Adding Shortening Model 500/600 Basic Operations and Procedures Basic Operations and Procedures Step Basic Operations and Procedures Filter Pump Motor PROTECTOR- Manual Reset Regular Maintenance ScheduleFrequency Filtering of Shortening Filtering of Shortening Filtering of Shortening Filtering Move the main power switch from Pump to OFF. This willShortening This union could be hot! Use protective cloth or glove Filter Pump Problem Prevention Changing the Filter EnvelopeHot water Changing the Filter Envelope Changing the Filter Envelope Cleaning the Frypot Cleaning the Frypot Step Model 500/600 LID Gasket ReversingLoss of pressure during a cook cycle LID Lubrication Limit Stop Adjustment Cleaning the Safety Relief Valve Limit Stop AdjustmentCheck & Tighten Element Spreader Bars Model 500 only Introduction Time and SET-POINT Programming ProgrammingMode Special ProgramSpecial Program Mode Problem Cause Correction Troubleshooting GuideError Code Table Error CodesDisplay Cause Panel Board Correction Error Code Table Display Cause Panel Board Correction Glossary Level also referred to as level indictor lines Also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corporation Box Eaton,OH Toll free in USA
Related manuals
Manual 100 pages 58.33 Kb

500, 600 specifications

Henny Penny has established itself as a leading name in the commercial cooking equipment industry, particularly known for its innovative fryers and cooking solutions. Among its notable products are the Henny Penny 500 and 600 series, which embody the brand's commitment to efficiency, reliability, and advanced technology.

The Henny Penny 500 series is designed for high-volume operations, perfect for restaurants, fast-food chains, and other foodservice establishments that require exceptional frying performance. This series features a highly efficient airflow design that ensures even cooking and reduces energy consumption. With a stainless-steel counter design, the Henny Penny 500 not only looks appealing but also offers durability and ease of cleaning, essential for maintaining hygiene in a busy kitchen.

One of the standout technologies in the 500 series is the advanced filtration system. This system helps to prolong oil life, reducing the frequency of oil replacements, which can save money and minimize waste. The intuitive control panel allows operators to manage cooking times and temperatures easily, resulting in consistent food quality. Additionally, the automatic basket lift feature enhances safety by reducing the chances of accidents during frying.

The Henny Penny 600 series takes this innovation further with additional features aimed at maximizing productivity. It shares many similarities with the 500 series but includes upgraded digital controls that allow for precise temperature management and programming options for various menu items. This added flexibility provides operators the ability to multitask effectively in a fast-paced kitchen environment.

Both series prioritize energy efficiency, with the 600 series particularly noted for its ability to minimize energy consumption without compromising performance. The fryers’ design incorporates energy-efficient heating elements and advanced insulation technology, ensuring quick recovery times and lower operating costs.

Furthermore, Henny Penny has incorporated user-friendly maintenance features in both series, such as easy-access panels for cleaning and routine maintenance checks. By focusing on operational ease and performance efficiency, the 500 and 600 series fryers exemplify Henny Penny’s dedication to providing commercial kitchens with the tools they need to succeed.

In summary, the Henny Penny 500 and 600 series reflect a blend of advanced technology and practical design, making them invaluable assets in any high-volume foodservice operation. With features such as high-efficiency frying, easy maintenance, and operator-centric controls, they stand as testaments to Henny Penny’s innovation in commercial cooking solutions.
Top Page Image Contents