Henny Penny 600, 500 warranty Electrical, Requirements, GAS Fryer

Page 22

 

Model 500/600

2-14. ELECTRICAL

The gas fryer requires 120-volt, single-phase, 60-Hertz, 10-amp,

REQUIREMENTS

3-wire grounded (earthed) service, or 230-volt, single-phase, 50-Hz,

(GAS FRYER)

5 amp, 1 phase service. The 120-volt gas fryer is factory equipped

 

with a grounded (earthed) cord and plug for your protection against

 

shock, and should be plugged into a three prong grounded (earthed)

 

receptacle. Do not cut or remove grounding (earthing) prong. A

 

wiring diagram is located behind the right side panel, and can be

 

accessed by removing the side panel. The 230-volt plug must conform

 

to all local, state, and national codes.

Do not disconnect the ground (earth) plug. This fryer MUST be adequately and safely grounded (earthed) or electrical shock could result. Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No. 70-(the current edition). In Canada, all electrical connections are to be made in accordance with CSA C22.1, Canadian Electrical Code Part 1, and/or local codes.

To avoid electrical shock, this appliance must be equipped with an external circuit breaker which will disconnect all ungrounded (unearthed) conductors. The main power switch on this appliance does not disconnect all line conductors.

2-12

1207

Page 21 Page 23
Image 22
Page 21 Page 23
Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Page Keep appliance area free and clear from combustibles Technical Data for CE Marked Products Table of Contents Table of Contents Pressure Heat Time Pressure FryerProper Care Assistance Model Variations Injury SafetyWhich, if not avoided, could result in death or serious Hazardous Situation WHICH, if notUnpacking Instructions IntroductionStep Unpacking Instructions Location Position and install fryer to prevent tipping or moveSelecting the Fryer Ment. Restraining ties may be used for stabilizationModel 500/600 GAS Supply GAS Piping Main gas line supplyHenny Penny Part No , which complies with GAS Piping GAS Leak Test Regulator SettingProcedure GAS PressureProcedure Shutdown ProcedureData Table Supply Wiring and Fusing for Electric Fryer Electrical Requirements Electric FryerRequirements ElectricalGAS Fryer Checking the Filter Pump Motor Bearings Operational ChecksPage Operating Controls Refer to Figure Description FunctionOperating Controls Control PanelDo not Pull this RING. Severe Burns from Operating ComponentsDescription Function Steam will ResultResult in the fryer building too much pressure. Severe Failure to clean the deadweight assembly daily couldInjuries and burns could result Is Under PRESSURE. HOT Shortening will Exhaust and Severe Burns will ResultGas Electric Operating Components Operating ControlsGAS Model Operating Controls Filling or Adding Shortening Model 500/600 Basic Operations and Procedures Basic Operations and Procedures Step Basic Operations and Procedures Filter Pump Motor PROTECTOR- Manual Reset Regular Maintenance ScheduleFrequency Filtering of Shortening Filtering of Shortening Filtering of Shortening Filtering Move the main power switch from Pump to OFF. This willShortening This union could be hot! Use protective cloth or glove Filter Pump Problem Prevention Changing the Filter EnvelopeHot water Changing the Filter Envelope Changing the Filter Envelope Cleaning the Frypot Cleaning the Frypot Step Model 500/600 LID Gasket ReversingLoss of pressure during a cook cycle LID Lubrication Limit Stop Adjustment Limit Stop Adjustment Cleaning the Safety Relief ValveCheck & Tighten Element Spreader Bars Model 500 only Programming Introduction Time and SET-POINT ProgrammingSpecial Program ModeSpecial Program Mode Troubleshooting Guide Problem Cause CorrectionError Code Table Error CodesDisplay Cause Panel Board Correction Error Code Table Display Cause Panel Board Correction Glossary Level also referred to as level indictor lines Also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corporation Box Eaton,OH Toll free in USA
Related manuals
Manual 100 pages 58.33 Kb

500, 600 specifications

Henny Penny has established itself as a leading name in the commercial cooking equipment industry, particularly known for its innovative fryers and cooking solutions. Among its notable products are the Henny Penny 500 and 600 series, which embody the brand's commitment to efficiency, reliability, and advanced technology.

The Henny Penny 500 series is designed for high-volume operations, perfect for restaurants, fast-food chains, and other foodservice establishments that require exceptional frying performance. This series features a highly efficient airflow design that ensures even cooking and reduces energy consumption. With a stainless-steel counter design, the Henny Penny 500 not only looks appealing but also offers durability and ease of cleaning, essential for maintaining hygiene in a busy kitchen.

One of the standout technologies in the 500 series is the advanced filtration system. This system helps to prolong oil life, reducing the frequency of oil replacements, which can save money and minimize waste. The intuitive control panel allows operators to manage cooking times and temperatures easily, resulting in consistent food quality. Additionally, the automatic basket lift feature enhances safety by reducing the chances of accidents during frying.

The Henny Penny 600 series takes this innovation further with additional features aimed at maximizing productivity. It shares many similarities with the 500 series but includes upgraded digital controls that allow for precise temperature management and programming options for various menu items. This added flexibility provides operators the ability to multitask effectively in a fast-paced kitchen environment.

Both series prioritize energy efficiency, with the 600 series particularly noted for its ability to minimize energy consumption without compromising performance. The fryers’ design incorporates energy-efficient heating elements and advanced insulation technology, ensuring quick recovery times and lower operating costs.

Furthermore, Henny Penny has incorporated user-friendly maintenance features in both series, such as easy-access panels for cleaning and routine maintenance checks. By focusing on operational ease and performance efficiency, the 500 and 600 series fryers exemplify Henny Penny’s dedication to providing commercial kitchens with the tools they need to succeed.

In summary, the Henny Penny 500 and 600 series reflect a blend of advanced technology and practical design, making them invaluable assets in any high-volume foodservice operation. With features such as high-efficiency frying, easy maintenance, and operator-centric controls, they stand as testaments to Henny Penny’s innovation in commercial cooking solutions.
Top Page Image Contents