h)Freeze Termination Diagnosis: After 5 min. in freeze, disconnect CB K5 FS connector. 15 sec. later appliance should switch out of the freeze cycle (15 second delay after FS opens before terminating the freeze cycle). If appliance remains in freeze longer than 15 sec. after FS removed, replace CB. If appliance switches with FS removed but would previously not switch out of freeze with FS connected (long freeze - 3 beep alarm), see "II.E. Float Switch Check and Cleaning."
Note: Normal freeze cycle will last 20 to 40 min. depending on model and conditions. Cycle times and pressures should follow performance data provided in this manual. See "VIII.A. Specification and Performance Data."
i)Short Freeze Cycle Diagnosis: Confirm water tank fills and overflows during 1 min. fill and harvest cycles. If not, check water supply filters, shut-off valve, WV screen. If water tank empties before 5 min. timer terminates and freeze cycle is short, check that CV is not leaking by (water flowing down the potable drain). If CV is leaking by, remove and clean CV, replace rubber seat and spring if necessary. If water tank is full, see "II.E. Float Switch Check and Cleaning" for erratic operating FS.
7)Pump-Out Cycle – LEDs 1, 3, and 2 are on (10/20 second pump-out).Timing of the first pump-out is dependent on CB. "E" CB first pump‑out is after the first freeze cycle. "G" CB first pump-out is determined by S4 dip switch 5 & 6. See the table below.
| "E" & "G" Control Board Settings | 1st Pump-Out |
| | | | | |
| S4 Dip Switch Setting | Pump-Out | "E" Control Board | "G" Control Board |
| No. 5 | No. 6 | Frequency |
| | |
| | | | | |
| OFF | OFF | Every cycle | After 1st freeze cycle | After 2nd freeze cycle |
| | | | | |
| ON | OFF | Every 2 cycles | | After 3rd freeze cycle |
| | | | | |
| OFF | ON | Every 5 cycles | | After 6th freeze cycle |
| ON | ON | Every 10 cycles | | After 11th freeze cycle |
| | | | | |
Comp and FMR continue, HGV energizes. If S4 dip switch 3 & 4 are set to 3 off and
4 on, LED 4 turns on and WV energizes. FM and LLV de‑energize. PM stops for 2 sec., then reverses for 10/20 sec. depending on pump‑out timer (S4 dip switch 3 & 4) setting. When the pump‑out timer terminates, pump‑out is complete. The pump-out frequency control (S4 dip switch 5 & 6) is factory set, and generally no adjustment is required. However, the pump‑out frequency control can be set to have a pump‑out occur every cycle, or every 2, 5, or 10 cycles. For details, see "III.C.4. Pump‑Out Frequency Control (S4 dip switch 5 & 6)."
Pump-Out Diagnosis: In the freeze cycle before pump-out (see table above), disconnect CB black K5 connector (FS connector) after 5 min. of freeze. Check that PM stops and re-starts and water is flowing down the drain through CV. If PM does not stop and re-start, check that CB LEDs 1, 3, and 2 are on. If not, replace CB. If LEDs 1, 3, and 2 are on and PM does not energize, check for 115VAC at CB K1 #5 (DBU) to neutral (W). If 115VAC is not present, replace CB. If 115VAC is present, make sure the drain line is not clogged and that CV is clean and operating properly.
Confirm FM and LLV de-energize. If FM or LLV is energized with LEDs 1, 3, and 2 on, replace CB.