Hoshizaki KMD-410MAH Water-Cooled Condenser, KMD-410MWHDrain Connection to an Open Drain System

Page 18

2. Water-Cooled Condenser

a) Connection to an Open Drain System

Condenser Water

Minimum Condenser

Condenser Drain

Minimum Condenser

Supply Inlet

Water Supply Line Size

Outlet

Drain Line Size

1/2" Female Pipe

1/4" Nominal ID Copper

1/2" Female Pipe

1/4" Nominal ID Hard

Thread (FPT)

Water Tubing or Equivalent

Thread (FPT)

Pipe or Equivalent

A condenser water supply line shut-off valve and drain valve must be installed.

In some areas, a back flow preventer may be required in the cooling water circuit.

In order to maintain the proper high side pressure, the condenser water supply inlet temperature must be in the 45°F to 90°F (7°C to 32°C) range.

Condenser

Drain Outlet

1/2” FPT

Condenser Water

Supply Inlet

1/2” FPT

Icemaker Drain

Outlet

3/4” FPT

Bin Drain Outlet 3/4” FPT

Icemaker Water

Minimum 1/4” Nominal ID

Supply Inlet

Copper Water Tubing

1/2” FPT

 

 

Icemaker Water Supply Line

 

Shut-Off Valve

 

Icemaker

Condenser Water Supply Line

Shut-Off Valve

 

 

 

 

Icemaker Water Supply Line

 

Drain Valve

 

 

Condenser Water Supply Line

Bin

Drain Valve

Be sure there is sufficient extra

 

 

Vent Tube

water supply line and drain line

 

for the appliance to be pulled

 

 

 

Minimum 3/4”

out for service.

 

 

 

Nominal ID

Separate piping to approved

 

Hard Pipe

drain. Leave a 2-inch (5-cm)

 

2-inch

vertical air gap between the

 

(5-cm)

end of each pipe and the drain.

 

air gap

 

Minimum 1/4” Nominal ID

Hard Pipe

Floor

KMD-410MWHDrain

Connection to an Open Drain System

Fig. 10

17

Image 18
Contents KMD-410MAH KMD-410MWH Hoshizaki AMERICA, INC Contents Important Safety Information Page Single Phase Model Number Specifications Electrical and Refrigerant DataDimensions/Connections KMD-410MAHKMD-410MWH II. Installation and Operating Instructions Checks Before InstallationHow to Remove Panels See Fig Location Setup Bin Control Installation Bin Control Lead Bushing Page Electrical Connection Water Supply and Drain Connections See , 10 or KMD-410MAH Water-Cooled Condenser KMD-410MWHDrain Connection to an Open Drain SystemConnection to a Closed Loop System Connection to a Closed Loop SystemFinal Checklist Startup III. Cleaning and Maintenance Instructions CleaningCleaning Procedure Page Float Switch Page Sanitizing Procedure Following Cleaning Procedure Storage Bin and Scoop MaintenanceStainless Steel Exterior Air Filters air-cooled model onlyPreparing the Icemaker for Periods of Non-Use Remove the water from the icemaker water supply lineDrain the water tank IV. Disposal Hoshizaki AMERICA, INC
Related manuals
Manual 65 pages 49.57 Kb

KMD-410MWH, KMD-410MAH specifications

The Hoshizaki KMD-410MWH and KMD-410MAH are premier ice makers, designed for commercial establishments that require high-efficiency ice production. These units stand out for their advanced features and technology that cater to the diverse needs of restaurants, bars, and hotels.

One of the primary features of the KMD-410 lineup is its impressive ice production capacity. With a production rate of up to 410 pounds of cube ice in a 24-hour period, each model ensures a steady supply of ice, which is essential for businesses with high demand. The ice produced is in the form of clear, hard cubes, ideal for beverage cooling, cocktail preparation, and food presentation.

Both models showcase the unique Hoshizaki ice-making system, which employs a direct cooling method. This technology uses individual stainless steel evaporators to produce ice, resulting in more uniform cubes and less waste. The stainless steel construction contributes to the durability of the units, making them suitable for rugged commercial environments.

Energy efficiency is another hallmark of the KMD-410MWH and KMD-410MAH. These machines are designed with an energy-saving mode that reduces power consumption without compromising ice production. This is critical for businesses looking to minimize operational costs while maintaining high standards of service.

User convenience is prioritized in these models through features like the easy-to-clean design. The internal components can be accessed quickly, allowing for simpler maintenance and sanitation processes. Additionally, the built-in cleaning cycle aids in maintaining ice purity and preventing bacterial growth, which is essential for food safety.

The KMD-410MAH also includes an advanced monitoring system with indicators for water usage and ice levels. This feature allows operators to keep track of performance and make necessary adjustments, ensuring that the ice maker operates at peak efficiency.

For installation flexibility, both models can be paired with various storage bins and dispensers, adapting to the layout of any establishment. Furthermore, they can be equipped with optional filtration systems that enhance water quality, further improving the taste and clarity of the ice produced.

In summary, the Hoshizaki KMD-410MWH and KMD-410MAH ice makers are exemplary choices for any business that demands high-quality, reliable ice production. Their robust features, energy-efficient operation, and user-friendly design make them indispensable assets in the hospitality and foodservice industries.