Hoshizaki IM-240AWME, IM-240AME Water Supplyand Drain Connections, Air-Cooled Model

ENGLISH

5)Seal the seam between the icemaker and the Storage Bin with food grade sealant.

6)Remove the Drain Pipe Collar and Drain Pan. Secure the Bin Control Switch to the Mounting Frame using the two bolts and flat washers provided. Fix the Bin Control Switch wiring with the two nylon ties. Place the Ice Chute on the Unit Frame, and refit the Drain Pan in its correct position. See Fig. 5.

	Unit Frame
	Ice Chute
	Mounting Frame
	Tie
Drain Pipe Collar	Washer
Packing
Drain Pan	Bolt
	Bin Control Switch

Fig. 5

7)Refit the panels in their correct positions.

8)Adjust the four legs on the bottom (adjustable from 0 to 25.4 mm) to have the icemaker perfectly horizontal. Use the spirit level. See Fig. 6.

Fig. 6 Adjust legs

4.ELECTRICALCONNECTIONS WARNING

THIS APPLIANCE MUST BE EARTHED

This icemaker requires an earth that meets the national and local electrical code requirements. To prevent possible severe electrical shock to individuals or extensive damage to equipment, install a proper earth wire to the icemaker. Remove the plug from the mains socket before any maintenance, repairs or cleaning is undertaken.

*This icemaker should not be installed:

a)Where the power supply is not within the range of 220 - 240V.

b)Where the icemaker cannot be plugged directly into its own power supply without using an extension cord or sharing a receptacle.

*The main control box fuse is rated at 5A and should only be replaced by a qualified service engineer.

*Usually an electrical permit and services of a licensed electrician are required.

*If the supply cord and the plug should need to be replaced, it should only be done by a qualified service engineer.

For the U.K. and the Republic of Ireland only

*The wires in the mains lead are coloured in accordance with the following code:

Green & Yellow = Earth Blue = Neutral

Brown = Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter E or by the

symbol or coloured Green or Green-and-Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red.

*Should the socket outlets in the installation site not be suitable for the plug supplied with your product, the plug must be removed (cut off if it is moulded on plug) and an appropriate plug fitted.

If the non-rewirable plug has been cut from the power supply cord, it must be disposed of. There should be no attempt to reuse it. Inserting such a plug into a socket elsewhere presents a serious risk of electrical shock.

*The non-rewirable plug must never be used without a fuse cover being fitted.

The correct replacement for the detachable fuse cover is identifiable from the manufacturer’s reference number stamped on the plug.

Supply of replacement fuse covers can be obtained from Hoshizaki Parts/Service Centres.

Fuses should be rated at 13A and approved to BS 1362.

5. WATER SUPPLYAND DRAIN CONNECTIONS

(For the U.K. only, the connections must be in accordance with current requirements of the Model Water Byelaws 1986 SI No. 1147)

*Only potable water should be used for the icemaker.

*Water supply pressure should be minimum 0.5 bar and maximum 8 bar. If the pressure exceeds 8 bar, use a proper pressure reducing valve. Do NOT throttle back the supply tap.

*A plumbing permit and services of a licensed plumber may be required in some areas.

*The icemaker drain is gravity flow, so ensure drain pipe has an adequate pitch or fall.

*Water should drain into an open trap.

*The Storage Bin has two drain outlets. The upper/outer one is for dump from the icemaker, and the lower/inner is for the Bin. The two drain lines must be separated to prevent a backflow into the Storage Bin.

*On water-cooled model, a back flow preventer may be required in the cooling water circuit.

[Air-Cooled Model]

1)Attach the angled end of white flexible inlet hose (accessory) to the G3/4 fitting on the left side of the icemaker as indicated, ensuring rubber sealing washer is correctly positioned. Hand tighten sufficiently to provide leak free joint (Fig. 7).

2)Attach the other end of inlet hose to the water tap (Fig. 8), noting washer is correctly positioned before hand tightening as above. It is a wise precaution to have a stop valve within easy reach.

3)Hand tighten grey flexible outlet hose (accessory) onto the R3/4 fitting on the left side of the Storage Bin as indicated, ensuring rubber washer is correctly positioned to obtain a leak free joint. The pipe can be cut to length as necessary to suit position of main drain.

Note: Jointing compounds should be approved and suitable for potable water use.

2