GE Monogram Professional Rangetop Before You Begin, Install The Wall Support Panels

Page 13
ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation

ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation

ACCESSORIES—30" TO 36" ADJUSTABLE BACKSPLASH (not included)

ACCESSORIES—30" TO 36" ADJUSTABLE BACKSPLASH (not included)WARNING:

To prevent ignition of combustible materials, the entire back wall above the range must be protected by a backsplash constructed of non-combustible material.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT: Save these instructions for local inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.

NOTE TO CONSUMER: Keep these instructions with your Owner’s Manual for future reference.

This backsplash adjusts to fit the space between the top of the range and the bottom of the hood, from 30" Min. to 36" Max. height.

Maximum shelf load-bearing weight is 40 lbs.

TOOLS AND MATERIALS REQUIRED

Gloves to protect against sharp edges

T-15 and #2 Phillips screwdrivers

Drill with 3/32" and 9/64" bits

Top Wall

Support

Safety glasses

 

Level

Top Cover

 

Pencil

with Shelf

 

This Kit Includes

Top wall support

 

Bottom wall support

Bottom Cover

• Top cover with shelf

 

Bottom cover

Bottom Wall Support

Hardware package with

 

9 Stainless Steel Torx 15 #8 self-tapping screws

– 9 Phillips #2 pan head wood #10 screws

– 3 Stainless Steel #2 truss head

Hardware

#10 screws (for alternatePackage installation method)

INSTALL THE WALL SUPPORT PANELS

BEFORE YOU BEGINWARNING: The wall support panels must be securely fastened to the wall. Failure to do so could result in damage or personal injury.

IMPORTANT: This backsplash is designed to cover the wall between the bottom of the hood and the top of the range. The vent hood should be installed over the rangetop or range before installing this backsplash.

Install and level the Range/Rangetop according to the product installation instructions.

Remove backsplash packaging and protective film.

Locate wall studs on each side. Where studs are not available, plan to use wall anchors (not provided).

Use a level to pencil 2 horizontal lines on the wall,

one 1/8" below the vent hood and the other 1/8" above the Range/Rangetop. This 1/8" space allows the cover panels to overlap the wall supports.

Secure the top wall support panel to the wall with 4 wood screws, through the outermost studs.

Use 4 wood screws to secure the bottom wall support panel. The center slot should be positioned at the top.

The gap between the top and bottom support panels will be covered by the top cover with shelf.

 

Secure the top

 

panel to the wall

1/8

with 4 wood

screws

 

Center

Wood

Secure

Arrow

Screws

the bottom panel

Wood Screws

 

to the wall with

1/8

 

4 wood screws

 

 

13

Image 13
Contents Instructions d’installation Installation InstructionsTables de cuisson professionnelles de 36 91 cm et de 48 122 cm Estufas profesionales de 36 91 cm y 48 122 cmBEFORE YOU BEGIN Safety InformationVent hood Combinations Completion Time - 1 to 3 hoursBACKSPLASH ACCESSORIES CONTENTSInstallation Instructions Installation PreparationADDITIONAL CLEARANCES PRODUCT DIMENSIONS AND CLEARANCES FOR 48” MODELSUniversal Utility Locations PRODUCT DIMENSIONS AND CLEARANCES FOR 36” MODELSControl panel projects forwards from standard depth cabinets INSTALLATION OPTIONSFront of deep cabinets can align with control panel beveled edge POWER SUPPLY LOCATIONS Installation PreparationTOOLS REQUIRED MATERIALS PROVIDEDStand clear. The ends of the cut metal banding may snap toward you REMOVE PACKAGINGSTEP 1 CUT THE COUNTERTOP OPENING InstallationCutout Opening with False Bottom STEP 3 CONNECT RANGETOP TO GAS STEP 2 INSTALL RANGETOPAssure that gas is turned off at the shut-off valve INSTALLATION CHECKLIST FINALIZE INSTALLATIONSTEP 4 CONNECT ELECTRICAL STEP 5 CHECK BURNERSOPTIONAL ACCESSORIES-12 HIGH BACKSPLASH ZX12B30PSS, ZX12B36PSS, ZX12B48PSS Accessory InstallationINSTALL 12 BACKSPLASH TOOLS AND MATERIALS REQUIREDACCESSORIES-30 TO 36 ADJUSTABLE BACKSPLASH not included ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory InstallationINSTALL THE WALL SUPPORT PANELS Maximum shelf load-bearing weight is 40 lbsINSTALL COVER PANELS cont INSTALL COVER PANELSSee alternate method if side access is blocked ALTERNATE METHOD When side access is blockedConvert LP Gas to Natural Gas Operation Convert Natural Gas to LP Gas Operation2 CONVERT THE REGULATOR TOOLS YOU NEEDED FOR CONVERSION3 CHANGE BURNER ORIFICES cont Installation Instructions for Gas Conversion4 CHANGE GRILL ORIFICE if present ZDP364, ZDP366, ZDP484, ZDP4865 CHANGE GRIDDLE ORIFICE if present 6 ADJUST BURNER FLAMESTemps d’installation - 1 à 3 heures Remarque à l’attention de l’installateurConsignes de sécurité AVANT DE COMMENCERPréparation de linstallation Consignes d’installationCaractéristiques TABLE DES MATIÈRESESPACES DE SÉPARATION SUPPLÉMENTAIRES AVERTISEMENTAVERTISEMENT Emplacements de raccord universelspanneau de commande OPTIONS DINSTALLATIONBord fini arrière du Bord arrièreEMPLACEMENT DES ALIMENTATIONS Préparation de l’installationOUTILS NÉCESSAIRES MATÉRIEL FOURNISORTEZ LAPPAREIL DE SON EMBALLAGE Ouverture découpée à faux-fond ÉTAPE 1 COUPEZ L’OUVERTURE DU PLAN DE TRAVAILÉTAPE 3 RACCORDEZ LA TABLE DE CUISSON AU GAZ ÉTAPE 2 INSTALLEZ LA TABLE DE CUISSONAssurez-vous que le gaz est coupé LISTE DE VÉRIFICATION POUR L’INSTALLATION TERMINEZ L’INSTALLATIONÉTAPE 5 VÉRIFIEZ LES BRÛLEURS ÉTAPE 4 RACCORDEZ AU RÉSEAU ÉLECTRIQUEINSTALLEZ LE DOSSERET 30 CM ACCESSOIRES EN OPTION-DOSSERET DE 30 CM 12 DE HAUTEURAVERTISSEMENT Ce dosseret OUTILS ET MATÉRIEL NÉCESSAIRESACCESSOIRES-DOSSERET AJUSTABLE 30-36 non fourni ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Installation d’accessoiresINSTALLEZ LES PANNEAUX DE SUPPORT MURAL AVERTISSEMENT Les panneauxINSTALLEZ LES PANNEAUX DE RECOUVREMENT suite INSTALLEZ LES PANNEAUX DE RECOUVREMENTOptez pour la méthode alternative si l’accès latéral est bloqué MÉTHODE ALTERNATIVE en cas d’obstruction de l’accès latéralConversion du propane au gaz naturel Conversion du gaz naturel au propane2 CONVERTIR LE RÉGULATEUR OUTILS DONT VOUS AUREZ BESOIN POUR LA CONVERSION4 CHANGEZ L’ORIFICE DU GRILL si installé Consignes d’installation pour la conversion de gaz3 CHANGEZ L’ORIFICE DU GRILL suite ORIFICES DE MIIJOTAGE ZDP3046 AJUSTEZ LES FLAMMES DU BRÛLEUR 5 CHANGEZ L’ORIFICE DE LA PLAQUE CHAUFFANTE si installéADVERTENCIA Información de seguridadCombinaciones de capuchas de ventilación PRECAUCIÓNCONTENIDOS Información de diseñoMODELOS DISPONIBLES ACCESORIOS PARA SALPICADEROADVERTENCIA DIMENSIONES Y ESPACIOS DEL PRODUCTO PARA MODELOS DE 48”ESPACIOS ADICIONALES Ubicaciones de los servicios públicos DIMENSIONES Y ESPACIOS DEL PRODUCTO PARA MODELOS DE 36”OPCIONES DE INSTALACIÓN HERRAMIENTAS REQUERIDAS Preparación para la instalaciónMATERIALES PROVISTOS MATERIALES REQUERIDOS NO PROVISTOSQUITE EL EMPAQUE Preparaciòn InstalaciónMantenga una distancia prudencial. Cuando se cortan, los extremos de los precintos de metal pueden golpearloPASO 1 CORTE LA ABERTURA DEL MOSTRADOR DE ENCIMERA InstalaciónAbertura de recorte con fondo falso PASO 3 CONECTE LA ESTUFA AL SUMINISTRO DE GAS PASO 2 INSTALE LA ESTUFAPASO 5 CONTROLE LOS QUEMADORES PASO 4 CONECTE LA ELECTRICIDADFINALICE LA INSTALACIÓN LISTA DE CONTROL DE LA INSTALACIÓNInstalación de accesorios ZX12B30PSS, ZX12B36PSS, ZX12B48PSS ANTES DE COMENZARACCESORIOS OPCIONALES - SALPICADERO ALTO DE 12” INSTALE EL SALPICADERO DE 12”ANTES DE COMENZAR ADVERTENCIA Los panelesACCESORIOS -SALPICADERO AJUSTABLE DE 30 A 36” no incluido INSTALELOSPANELESDESOPORTEDEPAREDINSTALE LOS PANELES DE CUBIERTA Instalación de accesorios ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSSINSTALE LOS PANELES DE CUBIERTA cont Ver el método alternativo si el acceso lateral se encuentra bloqueado2 CONVIERTA EL REGULADOR Conversión de gas natural a gas LP Conversión de gas LP a gas naturalHERRAMIENTAS NECESARIAS PARA LA CONVERSIÓN 3 CAMBIE LOS ORIFICIOS DE LOS QUEMADORES3 CAMBIE LOS ORIFICIOS DE LOS QUEMADORES cont Instrucciones de instalación para conversión de gas4 CAMBIE EL ORIFICIO DE LA PARRILLA si corresponde ZDP304 ORIFICIOS DE FUEGO LENTO5 CAMBIE EL ORIFICIO DE LA Ajuste la configuración de la hilera superior6 AJUSTE LAS LLAMAS DEL QUEMADOR PLANCHA si correspondePage Page GE Consumer & Industrial For Monogram local service in your area, callPara servicio técnico local Monogram en su área, llame al Appliances General Electric Company Louisville, KY 40225 ge.com