Lincoln Electric SVM100-A service manual Options / Accessories, Undercarriage Function

Page 28

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

C-1	ACCESSORIES

OPTIONS / ACCESSORIES

•Hand Amptrol (K812)

•Foot Amptrol (K870)

•Arc Start Switch (K814)

•Magnum Cooler Horizontal TIG Mounting Bracket (K559-2)

•Undercarriage (K932-1)

UNDERCARRIAGE FUNCTION

The Square Wave TIG 255 is designed to be used with a Lincoln K932-1 Undercarriage. Complete installation instructions are included with the K932-1 undercarriage. When the undercarriage is properly installed, the Square Wave TIG 255 lift bail is non- functional. Do not attempt to lift the power source with the undercarriage attached. The undercarriage is designed for hand moving only; mechanized towing can lead to injury and/or damage to the Square Wave TIG 255.

INSTALLATION OF FIELD

INSTALLED OPTIONS

Instructions for connecting the K932-1 Undercarriage and the K559-2 Magnum Cooler Horizontal TIG Mounting Bracket are included with those acces- sories.

Installation of the K812 Hand Amptrol, the K814 Arc

Start Switch and K870 Foot Amptrol are as follows:

Lift the Output Cover Door (if so equipped) on the Square Wave TIG 255. Feed the cable up through the strain relief holes in the base, and connect the 6-pin MS-type (Amphenol) connector to the Remote Receptacle (See Figure A.2). Secure with the thread- ed collar.

SQUARE WAVE TIG 255

Image 28

Contents Square Wave TIG Safety Electric Shock can killARC Rays can burn Fumes and Gases can be dangerousCylinder may explode if damaged Welding Sparks can cause fire or explosionElectric and Magnetic Fields May be dangerousPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation SectionInstallation Technical Specifications Square Wave TIGSafety Precautions High Frequency Interference ProtectionSelect Suitable Location StackingGround Connection Input ConnectionsInput Supply Connections Output Connections Reconnect ProcedureTIG Torch Connection Table A.1 Stick Electrode Cable ConnectionOperation Section Operation Operating InstructionsGeneral Warnings Fumes and GasesSection TOC Polarity Do not Switch AC & DC Recti Fier Power Source While Weld ING TIG Gtaw Single PhaseWork Connec Coolant Tion OutputDesign Features Advantages Operational Features and ControlsGeneral Description Recommended Processes and EquipmentWelding Capability LimitationsControls and Settings Control Panel KeysCase Front Controls LoadAccessory Operation TIG Welding Table B.1 Recommended Polarity Settings for TIG WeldingHand and Foot Amptrol Welding Operation TIG Welding GuidelinesTable B.2 Typical Current Ranges 1 for Tungsten Electrodes TIG Welding Sequence Operation 2-STEP ModeSquare Wave TIG 255 12/95 TIG Welding Sequence Operation 4-STEP Mode Auxiliary Power Advanced TIG Welding FeaturesALL Machines AC Wave Balance and Auto BalanceOverload Protection Square Wave TIG Accessories Section Accessories Options / AccessoriesInstallation of Field Installed Options Undercarriage FunctionMaintenance Section Maintenance MaintenanceRoutine and Periodic Maintenance Safety PrecautionsFigure D.1 General Assembly Exploded View Square Wave TIG Power Supply Block Logic Diagram Theory of Operation SectionTheory of Operation Input Line Voltage and Main TransformerOutput Rectification and Feedback Control High Voltage / High Frequency Circuit DC Welding Output DC Welding CircuitAC Welding Output AC Welding CircuitSCR Operation SCR Operation Square Wave TIGThermal Protection Troubleshooting & Repair Section 1TROUBLESHOOTING & Repair HOW to USE Troubleshooting GuideTroubleshooting & Repair PC Board Troubleshooting ProceduresTroubleshooting Guide Output Problems12/95 Square Wave TIG Troubleshooting & Repair Possible Areas of Misadjustments Problems SymptomsRecommended Course of Action Function Problems Troubleshooting Guide Troubleshooting & Repair TIG Mode Problems Troubleshooting & Repair Troubleshooting Guide TIG Welding Problems Troubleshooting & Repair Stick Welding Problems PC Board Connector Locations Figure F.1 Control Board ConnectorsTest Description Control Transformer T2 Voltage TestMaterials Needed Test Procedure Control BOXControl Transformer T2 Voltage Test Figure F.4 Control Board and TransformerPROTECTION/SNUBBER Board Continuity Test PROTECTION/SNUBBER Board Continuity Test Figure F.6 PROTECTION/SNUBBER Board Test Points Table F.6 Square Wave TIGARC Start Trigger Circuit Test ARC Start Trigger Circuit Test Figure F.9 PROTECTION/SNUBBER Board Test Points Static SCR Test Static SCR Test Figure F.11 Protection Board Plug LocationsActive SCR Test Active SCR Test Figure F.13 PROTECTION/SNUBBER Board Plug LocationsBattery Test Silicon Controlled Rectifier TestNormal Open Circuit Voltage Waveform DC Stick Mode Scope SettingsNormal Open Circuit Voltage Waveform AC Stick Mode Normal Open Circuit Voltage Waveform DC TIG Mode Normal Open Circuit Voltage Waveform AC TIG Mode Typical Output Voltage Waveform Machine Loaded DC TIG Mode Machine Loaded to 200 Amps AT 50 VDCMachine Loaded to 50 Amps AT 26VAC AC TIG Mode Auto Balance onMachine Loaded to 200 Amps AT 46 VAC Volts 5ms Typical SCR Gate Voltage WaveformVolts 2ms Troubleshooting & Repair FAN Motor and Blade Removal Tools RequiredFAN Motor and Blade Removal SCR Heat Sink Assembly Removal Materials RequiredSCR Heat Sink Assembly Removal Input Idle Amps Retest After RepairRecommended Meters for Machine Output Tests Retest After Repair cont’d Figure F.16 Transformer Lead Test PointsElectrical Diagrams Electrical Diagrams Control Board G2150 PTC1,PTC2 THERMISTOR-PTC,56 OHMS,90MAControl Board G2150 cont’d Square Wave TIG PROTECTION/SNUBBER Board L9255 CAPACITOR-CEMO,4700P,50V,10% Square Wave TIG Wiring Diagram Square Wave TIG Machine Schematic Square Wave TIG 6 a 0 a 7 a 8 a 3 CG2150 A C C TControl Board Schematic Square Wave TIG 255 cont’d G2150 Y P a DPROTECTION/SNUBBER Board Schematic Square Wave TIG 255 L9255 Keypad LED Board Square Wave TIG 255 L9212