GE ZGU385N, ZGU385L Model ZET1 or ZET938, Oven requires a separate, properly grounded

Page 14

Installation Options

COOKTOP INSTALLATION OVER A 30″ MONOGRAM SINGLE OVEN,

MODEL ZET1 OR ZET938

These cooktops may be installed over the Monogram ZET1 or ZET938 single oven. Both the cooktop and the oven must be installed according to each specific installation instruction.

–Allow 4″ Min. clearance from the top of the countertop to the top of the oven cutout.

POWER SUPPLY

The oven requires a separate, properly grounded

20 Amp, 3-wire 208 or 240 volt, 60 Hz power supply. The cooktop requires a separate 120V power supply. See page 8. Where codes permit, the gas shut-off valve may be located in an adjacent cabinet or other easily accessible location.

1-1/2″cabinet top

	Cooktop	″
	33-7/8″	25
	33-7/8″	2-1/2″min.
		2-1/2″min.
		19-1/8″

36″

4″ min. countertop

height

27-1/4″min. 28-1/2″min. 27-5/16″max.

28-5/8″max.

23-1/2″min.

C

L

C	25″
L

Use two 2x4’s or equivalent runners spaced 25″ centerline to centerline in the opening and flush with top of toekick.

Or elevate the oven floor to desired height. The support must be level, rigidly mounted and capable of supporting 200 lbs.

Use a 36″ or wider base cabinet.

•For best appearance, the cooktop should be centered over the oven.

14

Image 14

Contents Questions? Call 800.GE.CARES La section française commence à laBefore YOU Begin Safety InformationFor Your Safety What to do if YOU Smell GASContents Electrical RequirementsModels Available Installation PreparationTools YOU will Need For Installation Parts IncludedInstallation Above Cabinet Drawers Installation OptionsCooktop and ZVB36 Downdraft Vent Combination Installation Advance PlanningPRE-INSTALLATION Checklist Dimensions and Clearances Gas supply Power Supply LocationsOptional Combination Installations Electrical supplyInstall Pressure Regulator Installation InstructionsInstall the Cooktop Connect ElectricalAssemble BURNERS, Check Ignition Check ignitersBurners should be checked frequently Operation Checklist″ to EdgesInstallation Options ″ gap 23-5/16″total flat surface required at centerZTD910 28-1/2″ ZKD910 25-1/2″ 4 ″Dim. a 36″ ″ min. countertop Height Model ZET1 or ZET938Oven requires a separate, properly grounded 28-5/8″max 23-1/2″minTools YOU will Need for Conversion Safety InformationAdjust the Regulator Change Burner OrificesAdjust Burner Flames Convert LP Gas Model ZGU385LSMSS to Natural Gas Operation Installation Instructions for LP to Natural Gas Conversion Pour Votre Sécurité Information de la sécuritéAvant DE Commencer CI QUE Vous Devez Faire SI Voussentez LE GAZContenu Information de la sécurité Avertissement DébranchezBesoins D’ÉLECTRICITÉ Pièces Comprises Préparation à l’installationModèles Disponibles Matériaux Dont Vous Pourriez Avoir BesoinInstallation au-dessus des tiroirs des armoires Options D’INSTALLATIONInstallation de la combinaison four simple ZET1 ou ZET938 Planification AvancéeCollé sur la face Liste DE Vérification DE PRÉ-INSTALLATIONEmballage MousseDimensions ET Dégagements Alimentation de gaz Emplacements DE L’ALIMENTATION DE GAZInstallations de combinaison en option 30,5 cm 12 poAvertissement ne réutilisez Instructions d’installationInstallez LE Régulateur DE Pression suite Avertissement n’utilisezAvertissement allumer Vérifiez les allumeursLes brûleurs doivent être régulièrement vérifiés Liste DE VérificationBrûleur de la Mm surface de cuisson 1/4 po Options d’installation Surface DE CUISSON-SPÉCIFICATIONS D’INSTALLATIONDim. a 30 PO, Modèle ZET1 OU ZET938 Changez LES Orifices DES Brûleurs Renseignements SUR LA SécuritéOutils Nécessaires Pour LA Conversion EncolurePlus la valve qu’à sa position initiale Ajustez LA Flamme DU BrûleurQue sa position initiale Tester la stabilité de la flammeConvertir le modèle du gaz PL ZGU385LSMSS au gaz naturel Ajustez LA Flamme DU Brûleur GE Consumer & Industrial