Thermador PCG36, PCG48 Backguard Installation, Burner Test and Adjustment, Test Cooktop Burners

Page 15

Step 6: Backguard Installation

A Low Back backguard must be installed when there is less than a 12" clearance between combustible materials and back edge of cooktop. (See Figure 1 and Figure 5.) For island installations and other installations with over 12" clearance, an optional stainless steel trim channel is

available to cover the backguard mounting flanges. Attach the backguard before sliding the appliance into the final installed position. Follow Steps A through C below:

1.Slide backguard over the two flanges on the rear of the appliance. Fasten the front and back with the two screws (see A, Figure 11) provided.

2.Fasten the top of the backguard to the wall with two screws through the backguard. (See B, Figure 11.)

3.Place the backguard cap on top and fasten using the two counter-sink screws provided. (See C, Figure 11.)

C

B

A

 

 

 

Figure 11: Low Back Attachment

 

 

 

 

 

Low Back and Island Trim Model Numbers

 

 

 

 

 

 

Cooktop Size/Type

 

12” Low Back

Island Trim*

 

 

 

 

 

30”

 

PA30GLBC

PA30GITC

36”

 

PA36GLBC

PA36GITC

48”

 

PA48GLBC

PA48GITC

 

 

 

 

 

*Requires a minimum of 12” horizontal clearance between back of appliance and combustible materials.

Step 7: Burner Test and Adjustment

Install any loose components, such as burner caps and grates that may have been removed earlier.

Be certain that burner caps seat properly into the burner bases. Before testing operation of the appliance, verify that the unit and the gas supply have been carefully checked for leaks and that the unit has been connected to the electrical power supply. Turn the manual gas shut-off valve to the open position.

Test Cooktop Burners

Test Burner Ignition. Select a cooktop burner knob. Push in and turn counterclockwise to HI. The ignitor/spark module will produce a clicking sound. Once the air has been purged from the supply lines, the burner should light within four (4) seconds.

Test Flame: High Setting. Turn burner on to HI. See Figure 12 for appropriate flame characteristics. If any of the cooktop burners continue to burn mostly or completely yellow, verify that the burner cap is positioned properly on the burner base, then re-test. If flame characteristics do not improve, call Thermador.

Test Flame: Low Setting. Turn burner on to LO. Verify that the flame completely surrounds the burner. There should be a flame at each burner port and there should be no air gap between the flame and the burner. If any burners do not carry over, call Thermador.

The two far left burners feature XLO, causing the flame to cycle on and off when the knob is set to the XLO range. This is normal operation.

Repeat the Ignition and Flame Test procedures described above for each cooktop burner.

English 13

Image 15
Contents Installation Manual Table of Contents For Massachusetts Installations Data Rating Plate Before you BeginSelect Hood and Blower Models Important Installation InformationHood Placement Ventilation RequirementsImportant Notes Consider Make-Up AirCabinet Preparation Material Island 54 or 60 Wide Hood for 48 Cooktop Cooktop 4 to CenterlineRear Unpacking, Moving, Placing and Anchoring the Cooktop Griddle Tilt Adjustment not all modelsGas Requirements and Hookup Propane Gas RequirementsHook Up Grounding Method Electrical Power Supply Over-current Protection RequirementsTest Cooktop Burners Backguard InstallationBurner Test and Adjustment Low Back and Island Trim Model Numbers Cooktop Size/TypeSoft Blue Flames InstallerYellow Flames Yellow Tips on Outer ConesTo Clean and Protect Exterior Surfaces Avant de comencer Liste de vérification pour l’installateurSI Vous Sentez UNE Odeur DE GAZ AvertissementAlimentation électrique Fiche signalétiqueInstructions de sécurite RemarqueMise EN Garde Information importante à propos de l’installationChapitre 1 Exigences de ventilation Mise EN GuardeApport d’air Emplacement de la hotteAvis Choix du modèle de hotte et de ventilateurCuisson Largeur de Configuration de la Minimum recommandéOptions de ventilation Surface de cuissonRemarques Chapitre 2 Préparation de l’emplacementDe cuisson de 48 po Installation de supports latéraux des deux côtés 64,5 cm Arriére Partie inférieure de l’appareil Ajustement de linclinaison de la plaque de cuissonExigences pour le gaz naturel Exigence pour le gaz propaneRaccordement Connexions électriques Méthode de mise à la terreChapitre 7 Test et réglage de brûler Chapitre 6 Installation de la plaque de protectionListe finale de vérification Flamme jaunePointe jaune sur cône extérieur Flamme bleueNettoyage et protection des surfaces extérieures InstallateurPage Lista de chequeo de instalador Antes de comenzarQUÉ Hacer Cuando Huele a GAS AdvertenciaAlimentatión eléctrica Instrucciones de seguridadNota Placa con información del productoInformación importante para la instalación Paso 1 Requerimientos para la ventilaciónPrecaución Considerar aire de reposición AvisoSeleccionar la campana y el ventilador Colocar la campanaVentilador Anchura de Configuración de la Mínimo recomendadoOpciones de ventilación HornillaNotas Paso 2 Preparación de los gabinetesSuperficie de cocinar Figura 2 Instalar los soportes laterales ambos lados 4 a Entrada DE GAS Línea Central 23-5/16 Tablitadesoporte Importante Paso 3 Desempacar, mover, posicionar y jar la parrillaConexión Paso 4 Requerimientos de gas y conexionesAjuste de inclinación de la plancha Requerimientos para gas propanoMétodo de puesta a tierra ApagadoPaso 6 Instalación de la consola trasera de protección Paso 7 Probar y Ajustar el QuemadorRequerimientos para la protección de sobrecorriente Llama Azul Suave Probar la llama Calor alto. Cambie el quemador a HILlama amarilla Puntas Amarillas sobre ConosPara limpiar y proteger las superficies exteriores Remarques Notas Page
Related manuals
Manual 50 pages 10.82 Kb Manual 80 pages 58.61 Kb

PCG30, PCG48, PCG36 specifications

The Thermador PCG36, PCG48, and PCG30 are beautifully engineered professional-style gas cooktops that stand out for their performance, design, and innovative features. These models embody the ethos of Thermador, which is to provide culinary enthusiasts with the tools they need to create exceptional dishes at home.

One of the main features of these cooktops is their powerful Star® Burners. The PCG36 and PCG48 come equipped with up to five burners, including a highly efficient center burner that delivers up to 22,000 BTUs of heat. This powerful burner is ideal for searing, stir-frying, or boiling large pots of water quickly. The precise temperature control provided by these burners allows for a wide range of cooking techniques, from delicate sauces to high-heat frying.

Each model showcases a unique cooking surface design, offering both functionality and aesthetics. The heavy-gauge stainless steel construction not only provides durability but also creates a sleek, sophisticated look suitable for any luxury kitchen. The Cooktop’s continuous cast-iron grates ensure that pots and pans slide effortlessly across the surface, enhancing the overall cooking experience.

In addition to their robust performance, these models are equipped with advanced features such as patented ExtraLow® simmering technology, which delivers ultra-low heat settings perfect for melting chocolate or keeping sauces warm without scalding. This technology is ideal for chefs who require precise control over their cooking temperatures.

The Thermador PCG series also prioritizes safety with features like automatic re-ignition, which ensures that if a burner’s flame is extinguished, it will automatically relight. Safety is paramount, particularly in fast-paced kitchen environments, and this feature provides peace of mind while cooking.

Moreover, one of the standout characteristics of these cooktops is their compatibility with Thermador’s exclusive Freedom® cooktops, which allows for more flexible cooking configurations. This innovative design enables chefs to arrange their cooking stations according to their unique preferences.

In summary, the Thermador PCG36, PCG48, and PCG30 models exemplify precision, durability, and modern design. With their powerful burners, advanced technologies, and safety features, they cater to the demands of both amateur cooks and seasoned chefs. These cooktops are an excellent investment for anyone looking to elevate their culinary experience and kitchen aesthetics.