Whirlpool GGG388LXS, GGG390LXB, GGE388LXS, GGE388LXQ, GGG388LXQ manual Range Care, Self-Cleaning Cycle

RANGE CARE

Self-Cleaning Cycle

WARNING

Burn Hazard

Do not touch the oven during the Self-Cleaning cycle.

Keep children away from oven during

Self-Cleaning cycle.

Failure to follow these instructions can result in burns.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the Self-Cleaning cycle. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-ventilated room.

Self-clean the oven before it becomes heavily soiled. Heavy soil results in longer cleaning and more smoke.

Keep the kitchen well-ventilated during the Self-Cleaning cycle to help get rid of heat, odors, and smoke.

Do not block the oven vent(s) during the Self-Cleaning cycle. Air must be able to move freely. Depending on your model, see “Oven Vent” or “Oven Vents” section.

Do not clean, rub, damage or move the oven door gasket. The door gasket is essential for a good seal.

Prepare Oven:

■Remove the broiler pan, grid, cookware and bakeware and, on some models, the temperature probe from the oven.

■Remove oven racks to keep them shiny and easy to slide. See “General Cleaning” section for more information.

■Remove any foil from the oven because it may burn or melt, damaging the oven.

■Hand clean inside door edge and the 1½" (3.8 cm) area around the inside oven cavity frame, being certain not to move or bend the gasket. This area does not get hot enough during self-cleaning to remove soil. Do not let water, cleaner, etc., enter slots on door frame. Use a damp cloth to clean this area.

■Wipe out any loose soil to reduce smoke and avoid damage. At high temperatures, foods react with porcelain. Staining, etching, pitting or faint white spots can result. This will not affect cooking performance.

Prepare Cooktop:

■Remove plastic items from the cooktop because they may melt.

NOTE: The cooktop warming center will not function during the Self-Clean cycle.

IMPORTANT: Oven temperature must be below 400°F (205°C) to program a clean cycle.

Only 1 oven can be cleaned at a time.

Both oven doors lock when either oven is being cleaned.

How the Cycle Works

IMPORTANT: The heating and cooling of porcelain on steel in the oven may result in discoloring, loss of gloss, hairline cracks and popping sounds.

The Self-Cleaning cycle uses very high temperatures, burning soil to a powdery ash.

The clean time is set based on the usage of your oven; however, the time can be changed. Clean times range from 2 hours for light soil and between 3 hours and 4 hours for average to heavy soil.

The clean time can be set in 5 minute increments.

Once the oven has completely cooled, remove ash with a damp cloth. To avoid breaking the glass, do not apply a cool damp cloth to the inner door glass before it has completely cooled.

The oven light will not work during the Self-Cleaning cycle.

On some models, the surface elements will not work during the Self-Cleaning cycle.

When “LOCK” shows in the display, the door cannot be opened. To avoid damage to the door, do not force the door open when “LOCK” is displayed.

If an oven door is left open, “Door open clean cancelled” will appear in the display and a signal will beep. Close the door and press CLEAN.

NOTE: Only 1 oven can use the Self-Clean cycle at a time, and 24 hours must pass before the next Self-Clean cycle can begin.

To Self-Clean:

1.Close the oven door.

2.Press STEAM/PRECISE CLEAN option.

“PRESS ^ FOR UPPER OVEN” will scroll in the upper oven text area and “PRESS ^ FOR LOWER OVEN” will scroll in the lower oven text area.

3.Press the Temp/Time “up” or “down” arrow pads to select the desired oven.

“REMOVE RACKS” will scroll in the selected oven text area

for 5 seconds, followed by “SELECT OPTION.” In the lower oven text area, “PRESS ^ or ^ KEY” will scroll from right to left.

4.Press the Temp/Time “up” arrow pad. “Precise CLEAN” appears in the upper text display area, and “Push START” appears in the lower text display area.

5.Press START.

“Set clean time or Push Start” appears in the upper text display area.

6.Press the Temp/Time “up” or “down” arrow pad until the desired cleaning time is displayed.

7.Press START.

8.“UNLOCK IN XXX” will scroll in the upper or lower text area (depending on oven selection). “LOCKING” will scroll until the door is locked.

After the door is locked, “CLEAN UPPER” or “CLEAN LOWER” will scroll in the selected oven text area until the

clean cycle is finished.

17