Whirlpool SF360BEE W/N, SF395LEE Q/Z/B, TGS325E W, SF385PEE Q/Z, SF350BEE W Installing the GAS Line

Page 16

WARNING

Fire Hazard

pressure regulator

When you make gas line connections, espe- cially to the pressure regulator, do not make the connections too tight. If you do, you may crack the regulator (or pipe) and cause a gas leak, which could result in a possible fire, or explosion.

INSTALLING THE GAS LINE

The following procedure is for a typical gas line installation and its associated components to the gas range. Use pipe-joint compound that is made

90˚ elbow

adapter

adapter

1/2" to 3/4"

gas pipe

flexible line

gas shutoff valve

for use with natural and L.P. gas to seal all of the connections. Tighten all of the connections with an adjustable (pipe) wrench.

1.Turn all of the range knobs to OFF.

2.Remove the storage drawer so you can ac- cess the regulator.

3.Remove the plastic dust cap from the inlet of the pressure regulator.

4.Assemble the rigid or flexible gas line be- tween the gas supply pipe and the pressure regulator. Typical installations are shown in the following two illustrations. Use pipe-joint compound that is made for L.P. gas to seal the connections.

pressure regulator

90˚ elbow
90˚ elbow
nipple union	iron pipe
union
nipple	gas shutoff
	valve

1/2" to 3/4" gas pipe

A Typical Rigid Gas Line

A Typical Flexible Gas Line

5.Use a 15/16" combination wrench and channel lock pliers and tighten all of the fittings se- curely.

6.Seal all of the openings in the floor or wall around the range installation.

1-8

Image 16

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii Mobile Home Installation Range DimensionsGeneral Cabinet Dimensions Tools & Material YOU will Need ToolsAdditional Material Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property Damage Electronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Bake Burner Converting the Oven Burners for L.P. GASBroil Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Burner Removing a Sealed Burner & a VenturiRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module Removing the Ignitor Module & a Burner IgnitorRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing the Door Latch Solenoid Removing a Latch Sensing SwitchRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Error Codes Electronic Oven Controls Oven Temperature Calibration Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Strip Circuits BroilBake Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model Number Model and Serial Number ExplanationSerial Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for