Whirlpool SF375PEE Q/Z, SF395LEE Q/Z/B, TGS325E W, SF385PEE Q/Z, SF372BEE Q/Z, SF360BEE W/N 4321891

Page 79

2.Bake burner operates, but the broil burner will not come on.

a)Place the oven in the BROIL mode, set the oven thermostat to 350˚, and observe the broil igniter. If the igniter glows, go to step c. If the igniter does not glow, go to step b.

b)Disconnect power from the range, re- move the wires from the broil side of the gas safety valve, and connect an ohmmeter across the terminals of the

safety valve. If the meter reads ap- proximately 1 Ω, the problem is in another component of the broil circuit. If the meter reads infinity, replace the gas safety valve.

c)Connect an ampmeter to the broil cir- cuit. If the meter reads less than 3.2 amps, replace the broil igniter. If the meter reads over 3.2 amps, replace the gas safety valve.

3.The bake and broil burners will not oper- ate.

a)Place the oven in the BAKE mode, set the oven thermostat to 350˚, and ob- serve the bake igniter. Place the oven in the BROIL mode, and observe the broil ignitor.

Cooking Products Service Manual

Original July, 1996	4321891
© 1996 Whirlpool Corporation	Page 4-3

b)Disconnect power from the range and remove the wires from both sides of the gas safety valve. Check each side

of the valve with an ohmmeter. If the meter reads approximately 1 Ω on each side of the gas safety valve, the prob- lem is in another component. If the meter reads infinity on either side of the valve, replace the valve.

4.Bake burner will not turn off.

a)Observe the bake igniter. If the igniter is glowing, check the selector switch, the thermostat, and the electrical po- larity of AC receptacle for the power cord. If the igniter is not glowing, re- place the gas safety valve.

5.Broil burner will not turn off.

a)Observe the broil igniter. If the igniter is glowing, check the selector switch, the thermostat, and the electrical po- larity of AC receptacle for the power cord. If the igniter is not glowing, re- place the gas safety valve.

4-3

Image 79

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Electrical Shock Hazard Important Safety InformationPage Vii Viii Mobile Home Installation Range DimensionsGeneral Cabinet Dimensions Parts Supplied Illustrations Tools & Material YOU will NeedTools Additional MaterialEquipment & Property Damage Electrical Supply RequirementsPersonal Injury/Fire Hazard Electronic Ignition SystemIf you smell gas GAS Supply RequirementsInstalling the ANTI-TIP Bracket Installing the RangeInstalling the GAS Line Checking the Pressure Regulator Checking for LeaksPressure Regulator Remove the left and right venturi from the burner box Sealed BurnersConventional Burners Checking the Maintop Burner Operation LO F Lame Setting Adjustment Some ModelsAdjusting The Air Shutters Bake Burner Converting the Oven Burners for L.P. GASBroil Burner Control Knob Checking the Oven Burner OperationElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control To remove the oven door REMOVING/REINSTALLING the Oven DoorCooktop Burners Theory of OperationIgnitor System Operation Ignitor System OverviewBurner Ignitor Dual GAS Safety Valve Ignitor Does Not Glow Troubleshooting the Ignitor SystemWiring Diagram a Wiring Diagram B Sensor Oven ControlCOM Sensor Bake Function1030 Sensor Broil FunctionHI FO Clean Function Clean Time Oven Light Conventional Burner Models Sealed Burner ModelsSealed Burner Models Removing the MaintopBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Burner Removing a Sealed Burner & a VenturiRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module Removing the Ignitor Module & a Burner IgnitorRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Rear Burner BOX Screws Back of RangeRemove the top screws from the oven burner box Back of Range Removing the Door Latch Solenoid Removing a Latch Sensing SwitchRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Pull the knob off the control shaft if present Removing the Electronic Oven ControlRemoving the Manual Oven Light Switch Removing AN Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle Removing the Oven Door Handle TOP TRIM, & Outer Door GlassRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Troubleshooting Component Description & TestingDual GAS Safety Valve 4321891 GAS Outlet GAS Inlet TOP Burner GAS ValvesIgnitor Module TOP Burner Ignitor SystemOven Burner Igniters Automatic Oven Light Manual Oven Light Switch Some ModelsOven Light Door Latch Solenoid Door Latch AssemblyOven Temperature Sensor Troubleshooting Chart Replace the motor Error Codes Electronic Oven Controls Oven Temperature Calibration Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Tech Tips Wiring DiagramBake Ignitor Surface Burner Ignitor Module Ignitor Switches Quick Disconnect Plugs Strip CircuitsBroil BakeClock Display on CleanWhirlpool Models SpecificationsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model Number Model and Serial Number ExplanationSerial Number Length of Warranty Whirlpool will PAY for Whirlpool Warranty