Whirlpool SF350BEE W, SF395LEE Q/Z/B, TGS325E W, SF385PEE Q/Z, SF372BEE Q/Z Conventional Burners

Page 20

6.Removing one orifice spud at a time, use a 3/8" combination wrench, and replace the four color-coded natural gas orifice spuds with the same color L.P. gas orifice spuds. NOTE: When you are finished, place the natural gas orifice spuds in a plastic bag, and store them in a safe place for possible future use. Also, keep the literature that was supplied with the orifice spuds, in the same bag.

Remove and replace the

orifice spudsorifice spuds with the same color spuds.

notches

#70	#65	gas	#65	#68
black	brass	manifold	brass	nickel

3.Remove the four burners from the burner support bracket and from over the gas valves. NOTE: If installed, remove the shipping screws from the burners before you remove them.

burner shipping screw

burner

gas valve

L.R.	L. F.	R. F.	R.R.
7,500 BTU	8,500 BTU	8,500 BTU 6,500 BTU

7.Reassemble the range.

CONVENTIONAL BURNERS

1.Remove the grates from the burners.

2.Lift the maintop until the support rods lock .

4.Removing one orifice spud at a time, use a 3/8" combination wrench, and replace the natu- ral gas orifice spuds with the L.P. gas orifice spuds. NOTE: When you are finished, place the natural gas orifice spuds in a plastic bag, and store them in a safe place for possible future use. Also, keep the literature that was supplied with the orifice spuds, in the same bag.

orifice spuds	Remove and
	Remove and
	replace the
	orifice spuds.
	notches

brass	brass	brass	brass
	gas manifold
L.R.	L. F.	R. F.	R.R.
9,500 BTU	9,500 BTU	9,500 BTU 9,500 BTU

5.Reassemble the range.

1-12

Image 20

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii General Range DimensionsMobile Home Installation Cabinet Dimensions Tools & Material YOU will Need ToolsAdditional Material Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property DamageElectronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Broil Burner Converting the Oven Burners for L.P. GASBake Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Venturi Removing a Sealed Burner & a VenturiRemoving a Burner Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing a Burner Ignitor Removing the Ignitor Module & a Burner IgnitorRemoving the Ignitor Module Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing the Mechanical Latch Removing a Latch Sensing SwitchRemoving the Door Latch Solenoid Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Normal Codes Oven Temperature Calibration Electronic Oven ControlsError Codes Electronic Oven Controls Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Strip Circuits BroilBake Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Serial Number Model and Serial Number ExplanationModel Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for