Whirlpool SF360BEE W/N, SF395LEE Q/Z/B, TGS325E W Removing the GAS Safety Valve Pressure Regulator

Page 64

REMOVING THE GAS SAFETY VALVE &

PRESSURE REGULATOR

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

1.Pull the range away from the wall so that you can access the back.

2.Turn off the gas to the range and disconnect the power cord from the wall outlet.

3.Remove the bake burner from the oven (see page 3-23 for the procedure).

4.From behind the range, disconnect the four wires and the gas line fittings from the gas safety valve and the pressure regulator.

5.Remove the gas safety valve and the pres- sure regulator from the range.

6.If you are not replacing the complete assem- bly, separate the gas safety valve from the pressure regulator, then replace the defective component. NOTE: Apply pipe sealant that is recognized by U.L. to the threads of the fitting before you connect the two components to- gether again.

7.Mount the new gas safety valve and pressure regulator assembly to the range with its mount- ing hardware. NOTE: Make sure that the bake burner is positioned over the orifice hood.

BAKE BURNER

TO MAINTOP

 

 

 

 

BURNERS

TO BAKE

MOUNTING

 

RED

SHUTOFF VALVE

BRACKET

 

TERMINALS

GAS SAFETY

 

WHITE

VALVE

 

 

TO BROIL

 

 

BURNER

 

PRESSURE

 

 

REGULATOR

 

 

GAS INLET

BLUE

 

 

WHITE

 

 

 

GAS SHUTOFF LEVER

3-22

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii Mobile Home Installation Range DimensionsGeneral Cabinet Dimensions Tools & Material YOU will Need ToolsAdditional Material Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property DamageElectronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Bake Burner Converting the Oven Burners for L.P. GASBroil Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Burner Removing a Sealed Burner & a VenturiRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module Removing the Ignitor Module & a Burner IgnitorRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing the Door Latch Solenoid Removing a Latch Sensing SwitchRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Error Codes Electronic Oven Controls Oven Temperature Calibration Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Strip Circuits BroilBake Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model Number Model and Serial Number ExplanationSerial Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for
Top Page Image Contents