Whirlpool SF375PEE W/N, SF395LEE Q/Z/B, TGS325E W, SF350BEE W Checking the Maintop Burner Operation

Page 21

Cooking Products Service Manual

Original July, 1996	4321891
© 1996 Whirlpool Corporation	Page 1-13

CHECKING THE MAINTOP BURNER OPERATION

1.Install the maintop burner caps on the burn- ers.

2.If not already done, turn on the gas and electrical supplies to the range.

3.Push and turn each of the maintop burner knobs to the LITE position. You should hear a snapping sound as the burner ignitors spark. The gas at each burner should ignite after approximately 4-seconds. When this occurs, turn the knob to the HI setting. NOTE: Do not leave the knob in the LITE position after the burner lights, otherwise the ignitors will con- tinue to spark.

4.Check the maintop burners for the proper flame. The small inner cone should have a very distinct blue flame that is approximately 5/8" long. The outer cone will not be as distinct as the inner cone. If the flame is noisy or is blowing, there is too much air during combus- tion. If the flame is soft and not high enough, there is not enough air. If either of these conditions occur, adjust the air shutters, as shown on the next page.

LO F LAME SETTING ADJUSTMENT (SOME MODELS)

Some gas ranges have a low flame burner adjust- ment, located inside the shaft of each gas valve (see the illustration below). To adjust the flame:

1.Turn the gas valve knob to its LOW, or SIM- MER setting, and remove the control knob.

2.Adjust the screw inside the gas valve stem so that the flame size is as small as possible without going out when the valve is turned quickly from the LITE position to WARM posi- tion.

3.Turn off the burners and reinstall the knob.

5.Turn the maintop burners off.

1-13

Image 21

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Electrical Shock Hazard Important Safety InformationPage Vii Viii Range Dimensions Mobile Home InstallationGeneral Cabinet Dimensions Tools Tools & Material YOU will NeedAdditional Material Parts Supplied IllustrationsEquipment & Property Damage Electrical Supply RequirementsPersonal Injury/Fire Hazard Electronic Ignition SystemIf you smell gas GAS Supply RequirementsInstalling the ANTI-TIP Bracket Installing the RangeInstalling the GAS Line Checking the Pressure Regulator Checking for LeaksPressure Regulator Remove the left and right venturi from the burner box Sealed BurnersConventional Burners Checking the Maintop Burner Operation LO F Lame Setting Adjustment Some ModelsAdjusting The Air Shutters Converting the Oven Burners for L.P. GAS Bake BurnerBroil Burner Control Knob Checking the Oven Burner OperationElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control To remove the oven door REMOVING/REINSTALLING the Oven DoorCooktop Burners Theory of OperationIgnitor System Operation Ignitor System OverviewBurner Ignitor Dual GAS Safety Valve Ignitor Does Not Glow Troubleshooting the Ignitor SystemWiring Diagram a Wiring Diagram B Sensor Oven ControlCOM Sensor Bake Function1030 Sensor Broil FunctionHI FO Clean Function Clean Time Oven Light Conventional Burner Models Sealed Burner ModelsSealed Burner Models Removing the MaintopBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Sealed Burner & a Venturi Removing a BurnerRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module & a Burner Ignitor Removing the Ignitor ModuleRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Rear Burner BOX Screws Back of RangeRemove the top screws from the oven burner box Back of Range Removing a Latch Sensing Switch Removing the Door Latch SolenoidRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Pull the knob off the control shaft if present Removing the Electronic Oven ControlRemoving the Manual Oven Light Switch Removing AN Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle Removing the Oven Door Handle TOP TRIM, & Outer Door GlassRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Troubleshooting Component Description & TestingDual GAS Safety Valve 4321891 GAS Outlet GAS Inlet TOP Burner GAS ValvesIgnitor Module TOP Burner Ignitor SystemOven Burner Igniters Automatic Oven Light Manual Oven Light Switch Some ModelsOven Light Door Latch Solenoid Door Latch AssemblyOven Temperature Sensor Troubleshooting Chart Replace the motor Oven Temperature Calibration Electronic Oven Controls Error Codes Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Tech Tips Wiring DiagramBake Ignitor Surface Burner Ignitor Module Ignitor Switches Broil Strip CircuitsBake Quick Disconnect PlugsClock Display on CleanWhirlpool Models SpecificationsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model and Serial Number Explanation Model NumberSerial Number Length of Warranty Whirlpool will PAY for Whirlpool Warranty