Whirlpool TGS325E W, SF395LEE Q/Z/B, SF385PEE Q/Z, SF372BEE Q/Z, FGS335E Q Removing a Hinge Assembly

Page 73

Cooking Products Service Manual

Original July, 1996	4321891
© 1996 Whirlpool Corporation	Page 3-31

REMOVING A HINGE ASSEMBLY

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Remove the oven door (see page 1-20 for the procedure).

3.Remove the door handle, top trim, and outer door glass from the oven door (see page 3-30).

4.Position the oven door with the hinge assem- bly arms facing up.

5.Remove the flat-head screws from the bottom trim and remove the trim from the oven door.

CAUTION: Personal Injury Hazard—The hinge assembly arms are spring-loaded and can snap back when the arm pins are removed. Keep your fingers clear of the space between the oven door liner and the arms when you perform the following steps.

6.On the hinge assembly that you wish to re- move, place the bottom of your shoe against the end of the hinge , and move it just enough to remove the pin, then slowly allow the spring to move the hinge back to the “broil stop” position, and leave it there. IMPORTANT: Be careful not to disturb the arm when you re- move the hinge assembly on the next page.

HINGE PIN

LOCATION

HINGE IN “CLOSED” POSITION

HINGE PIN

LOCATION

HINGE IN “BROIL STOP” POSITION

3-31

Image 73

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Electrical Shock Hazard Important Safety InformationPage Vii Viii Mobile Home Installation Range DimensionsGeneral Cabinet Dimensions Tools Tools & Material YOU will NeedAdditional Material Parts Supplied IllustrationsEquipment & Property Damage Electrical Supply RequirementsPersonal Injury/Fire Hazard Electronic Ignition SystemIf you smell gas GAS Supply RequirementsInstalling the ANTI-TIP Bracket Installing the RangeInstalling the GAS Line Checking the Pressure Regulator Checking for LeaksPressure Regulator Remove the left and right venturi from the burner box Sealed BurnersConventional Burners Checking the Maintop Burner Operation LO F Lame Setting Adjustment Some ModelsAdjusting The Air Shutters Bake Burner Converting the Oven Burners for L.P. GASBroil Burner Control Knob Checking the Oven Burner OperationElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control To remove the oven door REMOVING/REINSTALLING the Oven DoorCooktop Burners Theory of OperationIgnitor System Operation Ignitor System OverviewBurner Ignitor Dual GAS Safety Valve Ignitor Does Not Glow Troubleshooting the Ignitor SystemWiring Diagram a Wiring Diagram B Sensor Oven ControlCOM Sensor Bake Function1030 Sensor Broil FunctionHI FO Clean Function Clean Time Oven Light Conventional Burner Models Sealed Burner ModelsSealed Burner Models Removing the MaintopBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Burner Removing a Sealed Burner & a VenturiRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module Removing the Ignitor Module & a Burner IgnitorRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Rear Burner BOX Screws Back of RangeRemove the top screws from the oven burner box Back of Range Removing the Door Latch Solenoid Removing a Latch Sensing SwitchRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Pull the knob off the control shaft if present Removing the Electronic Oven ControlRemoving the Manual Oven Light Switch Removing AN Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle Removing the Oven Door Handle TOP TRIM, & Outer Door GlassRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Troubleshooting Component Description & TestingDual GAS Safety Valve 4321891 GAS Outlet GAS Inlet TOP Burner GAS ValvesIgnitor Module TOP Burner Ignitor SystemOven Burner Igniters Automatic Oven Light Manual Oven Light Switch Some ModelsOven Light Door Latch Solenoid Door Latch AssemblyOven Temperature Sensor Troubleshooting Chart Replace the motor Error Codes Electronic Oven Controls Oven Temperature Calibration Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Tech Tips Wiring DiagramBake Ignitor Surface Burner Ignitor Module Ignitor Switches Broil Strip CircuitsBake Quick Disconnect PlugsClock Display on CleanWhirlpool Models SpecificationsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model Number Model and Serial Number ExplanationSerial Number Length of Warranty Whirlpool will PAY for Whirlpool Warranty