Whirlpool FGS335E W/N Removing a Sealed Burner & a Venturi, Removing a Burner, Removing a Venturi

Page 47

Cooking Products Service Manual

Original July, 1996	4321891
© 1996 Whirlpool Corporation	Page 3-5

REMOVING A SEALED BURNER & A VENTURI

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

REMOVING A BURNER

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Remove the grates and burner caps from the maintop.

3.Remove the screws from the defective burner.

SCREW

BURNER

MAINTOP

4.Lift the defective burner off the venturi and replace it with a new one, then reassemble the range.

REMOVING A VENTURI

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Lift the maintop and prop it up (use the proce- dure on page 3-2).

3.Lift the defective venturi from the burner box and replace it with a new one.

4.Lift the top of the coil around both venturi openings so they are even with the top.

5.Reassemble the range.

SLIDE COIL UP

TO TOP OF VENTURI

INSERT TAB

INTO SLOT

BURNER

BOX

BURNER

BURNER

IGNITOR

VENTURI

MAINTOP

3-5

Image 47

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Electrical Shock Hazard Important Safety InformationPage Vii Viii General Range DimensionsMobile Home Installation Cabinet Dimensions Parts Supplied Illustrations Tools & Material YOU will NeedTools Additional MaterialEquipment & Property Damage Electrical Supply RequirementsPersonal Injury/Fire Hazard Electronic Ignition SystemIf you smell gas GAS Supply RequirementsInstalling the ANTI-TIP Bracket Installing the RangeInstalling the GAS Line Checking the Pressure Regulator Checking for LeaksPressure Regulator Remove the left and right venturi from the burner box Sealed BurnersConventional Burners Checking the Maintop Burner Operation LO F Lame Setting Adjustment Some ModelsAdjusting The Air Shutters Broil Burner Converting the Oven Burners for L.P. GASBake Burner Control Knob Checking the Oven Burner OperationElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control To remove the oven door REMOVING/REINSTALLING the Oven DoorCooktop Burners Theory of OperationIgnitor System Operation Ignitor System OverviewBurner Ignitor Dual GAS Safety Valve Ignitor Does Not Glow Troubleshooting the Ignitor SystemWiring Diagram a Wiring Diagram B Sensor Oven ControlCOM Sensor Bake Function1030 Sensor Broil FunctionHI FO Clean Function Clean Time Oven Light Conventional Burner Models Sealed Burner ModelsSealed Burner Models Removing the MaintopBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Venturi Removing a Sealed Burner & a VenturiRemoving a Burner Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing a Burner Ignitor Removing the Ignitor Module & a Burner IgnitorRemoving the Ignitor Module Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Rear Burner BOX Screws Back of RangeRemove the top screws from the oven burner box Back of Range Removing the Mechanical Latch Removing a Latch Sensing SwitchRemoving the Door Latch Solenoid Mechanical Latch Switch Arms Removing the Upper Console Post Pull the knob off the control shaft if present Removing the Electronic Oven ControlRemoving the Manual Oven Light Switch Removing AN Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle Removing the Oven Door Handle TOP TRIM, & Outer Door GlassRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Troubleshooting Component Description & TestingDual GAS Safety Valve 4321891 GAS Outlet GAS Inlet TOP Burner GAS ValvesIgnitor Module TOP Burner Ignitor SystemOven Burner Igniters Automatic Oven Light Manual Oven Light Switch Some ModelsOven Light Door Latch Solenoid Door Latch AssemblyOven Temperature Sensor Troubleshooting Chart Replace the motor Normal Codes Oven Temperature Calibration Electronic Oven ControlsError Codes Electronic Oven Controls Digit Likely Cause Corrective Action Display Tech Tips Wiring DiagramBake Ignitor Surface Burner Ignitor Module Ignitor Switches Quick Disconnect Plugs Strip CircuitsBroil BakeClock Display on CleanWhirlpool Models SpecificationsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Serial Number Model and Serial Number ExplanationModel Number Length of Warranty Whirlpool will PAY for Whirlpool Warranty