Whirlpool SF385PEE Q/Z, SF395LEE Q/Z/B, TGS325E W, SF350BEE W Removing the Electronic Oven Control

Page 62

REMOVING THE ELECTRONIC OVEN CONTROL

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

1.Pull the range away from the wall so that you can access the back.

2.Turn off the gas to the range and disconnect the power cord from the wall outlet.

3.From behind the range, remove the upper access cover.

UPPER CONSOLE

OVEN CONTROL

REMOVE UPPER

ACCESS COVER

4.Pull the knob off the control shaft (if present).

OVEN CONTROL

CONSOLE PANEL

	OVEN	OVEN	ON		OFF	PUSH
DOOR	OVEN	HEATING				PUSH
DOOR		HEATING				TURN
	LOCKED/CLEANING			CLEAN			TO
				CLEAN			WARM
				TURN
				PUSH TO
				BROIL			200
				500			250
				500

450300

450 400 350

CONTROL KNOB

5.Without disconnecting any wires, remove the mounting screws from the electronic oven control and remove it from the back of the console.

OVEN CONTROL	MOUNTING
	SCREWS

CONSOLE PANEL

6.Mount the new electronic oven control to the upper console and install the knob (if appli- cable) on the control shaft.

7.Unplug the connectors from the old oven control, and reconnect them to the new oven control at the same callout (P1, P2, etc.) location.

8.Reassemble the range.

3-20

Image 62

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii General Range DimensionsMobile Home Installation Cabinet Dimensions Additional Material Tools & Material YOU will NeedTools Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property DamageElectronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Broil Burner Converting the Oven Burners for L.P. GASBake Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Venturi Removing a Sealed Burner & a VenturiRemoving a Burner Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing a Burner Ignitor Removing the Ignitor Module & a Burner IgnitorRemoving the Ignitor Module Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing the Mechanical Latch Removing a Latch Sensing SwitchRemoving the Door Latch Solenoid Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Normal Codes Oven Temperature Calibration Electronic Oven ControlsError Codes Electronic Oven Controls Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Bake Strip CircuitsBroil Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Serial Number Model and Serial Number ExplanationModel Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for