Whirlpool SF395LEE Q/Z/B, TGS325E W, SF385PEE Q/Z, SF372BEE Q/Z, SF360BEE W/N, SF350BEE W Oven Light

Page 84

OVEN LIGHT

Test Procedure

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before ser- vicing unit.

Failure to do so could result in death or electrical shock.

If the oven light does not work:

1.Remove the oven light bulb and test it for continuity. If the meter reads infinity, the bulb is defective. If the meter shows con- tinuity, reinstall the light bulb, and go to the next step.

2.Disconnect power from the range, and check the automatic oven light switch (and the manual light switch, if one is installed) for continuity with the switch contacts closed. Also make sure that none of the wire terminals are loose or shorted to the chassis.

3.Reconnect power to the range and touch the AC voltmeter leads to one of the light switch terminals and the neutral side of the line. If the meter reads zero, the wire from the terminal block of the switch is open. If the meter reads 120-volts AC, go to the next step.

4.Turn the light switch on and touch the AC voltmeter leads to the other light switch terminal and the neutral side of the line. If the meter reads zero, the switch is open. If the meter reads 120-volts AC, go to the next step.

5.Disconnect power from the range, and remove the rear panel.

6.Reconnect power to the range and touch the AC voltmeter leads to the red lead at the light socket terminals and neutral side of the line. If the meter reads zero, the wire from the light switch to the socket is open. If the meter reads 120-volts AC, go to the next step.

7.Touch the AC voltmeter leads to the white lead at the light socket terminals and neutral side of the line. If the meter reads zero, the socket is defective. If the meter reads 120-volts AC, the neutral line is open.

4-8

Image 84

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii Range Dimensions Mobile Home InstallationGeneral Cabinet Dimensions Tools & Material YOU will Need ToolsAdditional Material Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property DamageElectronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Converting the Oven Burners for L.P. GAS Bake BurnerBroil Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Sealed Burner & a Venturi Removing a BurnerRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module & a Burner Ignitor Removing the Ignitor ModuleRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing a Latch Sensing Switch Removing the Door Latch SolenoidRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Oven Temperature Calibration Electronic Oven Controls Error Codes Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Strip Circuits BroilBake Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model and Serial Number Explanation Model NumberSerial Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for