Whirlpool SF395LEE Q/Z/B, TGS325E W Removing the Oven Door Handle TOP TRIM, & Outer Door Glass

Page 72

REMOVING THE OVEN DOOR HANDLE,

TOP TRIM, & OUTER DOOR GLASS

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

REMOVING THE OVEN

DOOR HANDLE

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Remove the oven door (see page 1-20 for the procedure), and position it on the floor with the handle and outer door glass facing up.

3.Remove the two door handle screws from the liner side of the door. Remove the old handle and install the new one with the two screws.

4.Reinstall the oven door on the range.

REMOVING THE TOP TRIM & OUTER DOOR GLASS

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Remove the oven door (see page 1-20 for the procedure), and position it on the floor with the handle and outer door glass facing up.

3.Raise the top of the door and remove the two screws that secure the top of the door trim and the handle to the door liner, then remove the handle and top trim.

4.Lift the outer door glass off the door and set the new glass in its place so that the bottom edge is against the bottom trim.

5.Install the new top trim and handle on the oven door and secure them in place with their two mounting screws.

6.Reinstall the oven door on the range.

MOUNTING SCREWS

TOP TRIM

HANDLE

OUTER DOOR

GLASS

SET GLASS

BOTTOM TRIM

3-30

Image 72

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Important Safety Information Electrical Shock HazardPage Vii Viii Range Dimensions Mobile Home InstallationGeneral Cabinet Dimensions Tools & Material YOU will Need ToolsAdditional Material Parts Supplied IllustrationsElectrical Supply Requirements Equipment & Property DamageElectronic Ignition System Personal Injury/Fire HazardGAS Supply Requirements If you smell gasInstalling the Range Installing the ANTI-TIP BracketInstalling the GAS Line Checking for Leaks Checking the Pressure RegulatorPressure Regulator Sealed Burners Remove the left and right venturi from the burner boxConventional Burners LO F Lame Setting Adjustment Some Models Checking the Maintop Burner OperationAdjusting The Air Shutters Converting the Oven Burners for L.P. GAS Bake BurnerBroil Burner Checking the Oven Burner Operation Control KnobElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control REMOVING/REINSTALLING the Oven Door To remove the oven doorTheory of Operation Cooktop BurnersIgnitor System Overview Ignitor System OperationBurner Ignitor Dual GAS Safety Valve Troubleshooting the Ignitor System Ignitor Does Not GlowWiring Diagram a Wiring Diagram B Oven Control SensorCOM Bake Function Sensor1030 Broil Function SensorHI FO Clean Function Clean Time Oven Light Sealed Burner Models Conventional Burner ModelsRemoving the Maintop Sealed Burner ModelsBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Sealed Burner & a Venturi Removing a BurnerRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module & a Burner Ignitor Removing the Ignitor ModuleRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Back of Range Rear Burner BOX ScrewsRemove the top screws from the oven burner box Back of Range Removing a Latch Sensing Switch Removing the Door Latch SolenoidRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Removing the Electronic Oven Control Pull the knob off the control shaft if presentRemoving AN Oven Light Switch Removing the Manual Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle TOP TRIM, & Outer Door Glass Removing the Oven Door HandleRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Component Description & Testing TroubleshootingDual GAS Safety Valve 4321891 TOP Burner GAS Valves GAS Outlet GAS InletTOP Burner Ignitor System Ignitor ModuleOven Burner Igniters Manual Oven Light Switch Some Models Automatic Oven LightOven Light Door Latch Assembly Door Latch SolenoidOven Temperature Sensor Troubleshooting Chart Replace the motor Oven Temperature Calibration Electronic Oven Controls Error Codes Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Wiring Diagram Tech TipsBake Ignitor Surface Burner Ignitor Module Ignitor Switches Strip Circuits BroilBake Quick Disconnect PlugsClean Clock Display onSpecifications Whirlpool ModelsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model and Serial Number Explanation Model NumberSerial Number Whirlpool Warranty Length of Warranty Whirlpool will PAY for