Whirlpool SF372BEE Q/Z, SF395LEE Q/Z/B, TGS325E W, SF385PEE Q/Z Removing the Inner Door Glass

Page 75

Cooking Products Service Manual

Original July, 1996	4321891
© 1996 Whirlpool Corporation	Page 3-33

REMOVING THE INNER DOOR GLASS

WARNING

Electrical Shock Hazard

Disconnect from electrical supply before servic- ing unit.

Failure to do so could result in death or electri- cal shock.

CAUTION: When you work on the gas range, be careful when handling the sheet metal parts. Sharp edges may be present, and you can cut yourself if you are not careful.

1.Turn off the gas to the range and disconnect the power cord from the wall outlet.

2.Remove the oven door (see page 1-20 for the procedure).

3.Remove the door handle, top trim, and outer door glass from the oven door (see page 3-30).

4.Remove the flat-head screws from the bottom trim and remove the trim from the oven door.

5.Remove one of the hinge assemblies from the oven door (see page 3-31).

6.Lift the side of the insulation retainer and slide it out from under the remaining hinge assem- bly.

7.Fold back the door insulation, and remove the defective inner door glass from the metal frame.

8.If you are replacing the window seal, (the rope-type seal around the metal frame), re- move and replace it at this time.

9.Install the new inner door glass in the metal frame.

INNER	METAL
DOOR	FRAME
GLASS
	DOOR
	LINER

10.Position the insulation around the metal frame.

11.Reinstall the insulation retainer in the door so the edge is under the hinge assembly.

12.Position the arm on the hinge assembly to be installed to the “broil stop” position, then mount it to the oven door with its two flat-head screws. Make sure that the tab at the top of the hinge fits into the slot in the door liner before you mount the screws.

13.Using the bottom of your shoe, press down on the hinge assembly arm, and insert the pin into the hole in the arm.

14.Mount the bottom trim to the oven door with its mounting screws.

15.Mount the outer door glass, top trim, and the door handle to the door.

16.Reinstall the oven door on the range.

3-33

Image 75

Contents Freestanding SELF-CLEAN GAS Range Roper Table of Contents Wiring Diagram Electrical Shock Hazard Important Safety InformationPage Vii Viii Range Dimensions Mobile Home InstallationGeneral Cabinet Dimensions Parts Supplied Illustrations Tools & Material YOU will NeedTools Additional MaterialEquipment & Property Damage Electrical Supply RequirementsPersonal Injury/Fire Hazard Electronic Ignition SystemIf you smell gas GAS Supply RequirementsInstalling the ANTI-TIP Bracket Installing the RangeInstalling the GAS Line Checking the Pressure Regulator Checking for LeaksPressure Regulator Remove the left and right venturi from the burner box Sealed BurnersConventional Burners Checking the Maintop Burner Operation LO F Lame Setting Adjustment Some ModelsAdjusting The Air Shutters Converting the Oven Burners for L.P. GAS Bake BurnerBroil Burner Control Knob Checking the Oven Burner OperationElectronic Oven Control These conditions occur, proceed to the next Electronic Oven Control To remove the oven door REMOVING/REINSTALLING the Oven DoorCooktop Burners Theory of OperationIgnitor System Operation Ignitor System OverviewBurner Ignitor Dual GAS Safety Valve Ignitor Does Not Glow Troubleshooting the Ignitor SystemWiring Diagram a Wiring Diagram B Sensor Oven ControlCOM Sensor Bake Function1030 Sensor Broil FunctionHI FO Clean Function Clean Time Oven Light Conventional Burner Models Sealed Burner ModelsSealed Burner Models Removing the MaintopBurner Ignitor Maintop Removing the Maintop Conventional Burner Models Removing a Sealed Burner & a Venturi Removing a BurnerRemoving a Venturi Removing a Conventional Burner Removing a Spark Ignitor Switch & GAS Valve Removing the Ignitor Module & a Burner Ignitor Removing the Ignitor ModuleRemoving a Burner Ignitor Ignitor Module Conventional Burner Models Side of Upper Console Locking TAB WHT BRN Removing the Oven Door Latch & Actuator ROD Rear Burner BOX Screws Back of RangeRemove the top screws from the oven burner box Back of Range Removing a Latch Sensing Switch Removing the Door Latch SolenoidRemoving the Mechanical Latch Mechanical Latch Switch Arms Removing the Upper Console Post Pull the knob off the control shaft if present Removing the Electronic Oven ControlRemoving the Manual Oven Light Switch Removing AN Oven Light SwitchRemoving the GAS Safety Valve Pressure Regulator Removing the Bake Burner & Ignitor Removing the Broil Burner & Ignitor Removing the Oven Temperature Sensor Removing a Side Panel Right Side Panel Removing AN Oven Light Socket Removing the Oven Door Gasket Removing the Oven Door Handle Removing the Oven Door Handle TOP TRIM, & Outer Door GlassRemoving a Hinge Assembly Reassemble the rest of the door and install it Removing the Inner Door Glass Removing the Storage Drawer Glides Troubleshooting Component Description & TestingDual GAS Safety Valve 4321891 GAS Outlet GAS Inlet TOP Burner GAS ValvesIgnitor Module TOP Burner Ignitor SystemOven Burner Igniters Automatic Oven Light Manual Oven Light Switch Some ModelsOven Light Door Latch Solenoid Door Latch AssemblyOven Temperature Sensor Troubleshooting Chart Replace the motor Oven Temperature Calibration Electronic Oven Controls Error Codes Electronic Oven ControlsNormal Codes Digit Likely Cause Corrective Action Display Tech Tips Wiring DiagramBake Ignitor Surface Burner Ignitor Module Ignitor Switches Quick Disconnect Plugs Strip CircuitsBroil BakeClock Display on CleanWhirlpool Models SpecificationsMain Chassis Features 4321891 SF375PEE W/N SF375PEE Q/Z SF385PEE W/N Burner BTU Right Rear 500 BTU SF375PEE W/N SF375PEE Q/Z SF385PEE W/N SF385PEE Q/Z SF385PEE Q/Z SF395LEE Q/Z/B Oven Door Features Oven Door Type Roper Models FGS335E W/N FGS335E Q Oven Door Handle Estate Model TGS325E W 3196297A Model and Serial Number Explanation Model NumberSerial Number Length of Warranty Whirlpool will PAY for Whirlpool Warranty