Cornelius ICE FROST Programming Electronic Touch PAD, Main Power Switch, Auger ON/OFF Button

Page 13

Ice Frost Operator’s Manual

PROGRAMMING ELECTRONIC TOUCH PAD

To lower the control cover, use a coin or other object to turn the keyless lock to the horizontal position, in order to access the operating panel (controls are located on the right side of the unit).

Main Power Switch

•Turns unit ON.

•Selects 12/24 time clock or Fo/Co tempera- ture display when turned ON while simulta- neously depressing the auger button.

•Sets current time when turned ON while simultaneously depressing the “PRESS TO SELECT FUNCTION” button.

Auger ON/OFF Button

•Turns auger ON and OFF when main power switch is ON.

•Must be ON to permit COLD time to be reset.

•Must be ON to activate the “PRESS TO SELECT FUNCTION” button to select manual “OFF”, “FREEZE”, or “COLD” functions.

FIGURE 9

PRESS TO SELECT FUNCTION Button

•Used to manually select “OFF”, FREEZE”, or “COLD” functions when auger is turned ON.

•Accesses COLD timer reset mode when depressed for an extended period when auger is turned ON.

•Locks in hours, minutes and final time set- tings after they are reset using the “AUTO TIMER” button.

•Does not function when light on “AUTO TIMER” button is illuminated.

“AUTO TIMER” Button

•Turns auto COLD mode ON or OFF (light on switch indicates when auto COLD mode is activated).

•Used to adjust the hours and minutes set- tings when readjusting current time or auto COLD timer.

To Enter Time Programming on Initial Installation or in the Event of Service

1.Turn the power switch OFF.

2.Press and hold the left “PRESS TO SELECT FUNCTION” button and turn ON the power switch. Release the “PRESS TO SELECT FUNCTION” button when the hour digits start blinking.

3.Set the hour by pressing the “AUTO TIMER” clock button until the appropriate hour is shown.

NOTE: When using a 12 hour clock the time is P.M. when the dot at the bottom right corner of the LED display is lit; A.M. when dot is not lit.

4.Press the left “PRESS TO SELECT FUNCTION” button to set the minutes, then press the “AUTO TIMER” clock button until the appropriate minutes are set.

5.Press the “PRESS TO SELECT FUNCTION” button one more time to save your settings.

© 2004-2006, IMI Cornelius Inc.

- 9 -

Publication Number: M620919596OPR

Page 12 Page 14
Image 13
Page 12 Page 14
Contents ICE Frost Page Table of Contents Page Technical Data Important Warnings and AdviceTransportation Indications Plate DataConnecting the Electricity Mains InstallationIce Frost Generic Pre-mix Connection DiagramsDescription ConnectionInlet for CO2 45 to 60 psi CO2 gas cylinder Ice Frost Generic Post-mixSafety Probe Alarms only for ICE Frost Generic Pre-mix Alarms1st Filling Time-out Filling Time-outSystem Over Temperature Alarm Corrective Action Filter Cleaning AlarmCondition Bowl Loading Operations Brix Procedure Auto Timer Button Main Power SwitchProgramming Electronic Touch PAD Auger ON/OFF ButtonOperate in Automatic Mode with Cold Timer Activated Setting Cold Timer Night SettingOperate in Manual Mode without Cold Timer Activated Consistency Adjustment Viewing the Bowl TemperaturePost MIX Systems Operations Quarterly Cleaning and SanitationBowl Lid Cap Page Page Restricted AIR Flow Alarm Special MaintenancePressure and Level Control Card General Features Electronic Bowl Monitoring and Safety SystemElectronic Monitoring OFF Condition 1st Filling ConditionManaging the Bowl Levels Safety Probes only for ICE Frost Generic Pre-mixSumming Up Wiring Diagram Vfcb POST-MIX 115V/60HZ Vfcb PRE-MIX 230V/50HZ Vfcb POST-MIX 230V/50HZ Problem Possible Cause Solution TroubleshootingProduct Brix/ratio is too low ProblemProblem Possible Cause Solution IMI Cornelius Inc

ICE FROST specifications

Cornelius ICE FROST is a revolutionary ice dispensing solution that has redefined the way the foodservice industry approaches ice production and distribution. Designed for high-capacity environments, such as restaurants, hotels, and convenience stores, the ICE FROST system delivers consistent, high-quality ice while maximizing efficiency and reliability.

One of the standout features of the ICE FROST is its innovative ice-making technology. The system uses a unique air-cooled condenser coupled with a high-efficiency compressor, allowing it to operate effectively at varying ambient temperatures. This means that regardless of the conditions in the kitchen or service area, the ICE FROST ensures a steady supply of ice, minimizing the risk of downtime during peak hours.

In terms of capacity, the ICE FROST can produce a substantial amount of ice daily, tailored to meet the demands of busy establishments. Typically, it can generate up to 1,000 pounds of ice per day, depending on the specific model and configurations. This high output is complemented by a spacious storage bin that holds significant quantities of ice, reducing the frequency of refills and allowing for uninterrupted service.

Another key characteristic of the ICE FROST system is its user-friendly interface. The intuitive controls enable easy operation and allow staff to monitor production levels effortlessly. The machine is also designed for easy access and maintenance, with features such as removable panels and a self-cleaning option that simplifies the upkeep process. This focus on user experience not only enhances operational efficiency but also extends the lifespan of the equipment.

Energy efficiency is a major consideration for the modern foodservice establishment, and the ICE FROST excels in this area. With industry-leading energy consumption ratings, it helps businesses reduce operating costs while maintaining optimal productivity. Furthermore, its eco-friendly refrigerants align with contemporary sustainability practices, making it a responsible choice for environmentally conscious operators.

In conclusion, Cornelius ICE FROST stands out as a versatile, efficient, and reliable ice dispensing solution. Its combination of high production capacity, advanced technology, user-centric design, and energy efficiency makes it an essential asset for any foodservice operation. Whether used for beverages, food preservation, or other applications, the ICE FROST system ensures that businesses can meet the ice demands of their customers without compromise.
Top Page Image Contents