Cornelius 326142000 service manual Connecting Plain Water Inlet Supply Line to Unit

Page 17

WARNING: CO2 displaces oxygen. Strict attention must be observed in the prevention of CO2 (carbon dioxide) gas leaks in the entire CO2 and soft drink system. If a CO2 gas leak is suspected, particularly in a small area, immediately ventilate the contaminated area before

attempting to repair the leak. Personnel exposed to high concentration of CO2 gas will experience tremors which are followed rapidly by loss of consciousness and suffocation.

1.Unscrew protector cap (with chain attached) from CO2 cylinder valve. Open CO2 cylinder valve slightly counterclockwise to blow any dirt or dust from outlet fitting before installing primary CO2 regulator, then close valve.

2.Remove shipping plug from primary CO2 regulator assembly coupling nut and make sure gasket is in place inside nut. Install regulator assembly on CO2 cylinder so gages can be easily read, then tighten coupling nut. DO NOT OPEN CO2 CYLINDER VALVE AT THIS TIME.

CONNECTING SOFT DRINK TANKS CO2 LINES TO PRIMARY CO2 REGULATOR ASSEMBLY

(see Figure 2)

1.Connect soft drink tanks CO2 lines to primary CO2 regulator manifold assembly as shown in Figure 2.

2.Install gas quick disconnects on ends of soft drink tanks CO2 lines. DO NOT CONNECT CO2 LINES TO TANKS AT THIS TIME.

PREPARING UNIT SYRUP INLET LINES FOR CONNECTION TO SOFT DRINK TANKS

(see Figure 2)

1.Route Unit syrup inlet lines, labeled No. 1 and No. 2, out through hole provided in Unit base to soft drink tanks location.

2.Install liquid disconnects on ends of Unit syrup inlet lines. DO NOT CONNECT SYRUP LINES TO TANKS AT THIS TIME.

CONNECTING PLAIN WATER INLET SUPPLY LINE TO UNIT

(see Figure 2)

NOTE: IMI Cornelius Inc. recommends that a water shutoff valve and water filter be installed in plain water inlet supply line (see Figure 2). A Cornelius Water Filter (P/N 313860000) and Quick Disconnect Set (P/N 313867000) are recommended.

1.Before connecting plain water inlet supply line to Unit, open shutoff valve in water supply line for a period of time to flush out any metal shavings.

2.Route water inlet line out through hole in bottom of Unit base.

NOTE: Carbonator plain water inlet adjustable water pressure regulator (see Figure 12) is factory adjusted to 45-psi and should not be readjusted.

3.Connect Unit water inlet line to plain water inlet supply line (12-psi minimum pressure). Seal connection with TAPERED GASKET, BLACK (item 5). DO NOT OPEN WATER INLET SUPPLY LINE SHUTOFF VALVE AT THIS TIME.

326142000

10

Page 16 Page 18
Image 17
Page 16 Page 18
Contents This Document Contains Important Information FCB SOLID-STATE Post MIX DispenserTable of Contents Table of Contents cont’d Programming Main Menu Selection Onto Message Display Dispensing Valves Caged O-RINGS and Beaters Drive‘‘VIS READ’’ Actual Viscosity Readout of Product Troubleshooting Control Panel Switches and FaultServicing Carbonator Water Pump Double Liquid Check Replacing Freeze Cylinder Beater Drive Shaft BearingGeneric Flavor Tabs Service Tools ‘‘ERROR 1’’ or ‘‘ERROR2’’ Fault Message Goes on DuringFreeze Cylinder Automatic Defrost Cycle does not List of FiguresTotals Displayed Cycles and Hours Totals Menu List of Figures CONT’DList of Tables Unit Description General DescriptionDefrost Systems Theory of Operation‘‘WAKE UP’’ Wake UP Time ‘‘SLEEP’’ Sleep TimeManual Defrost System Automatic Defrost SystemFlow Diagram Identification of LOOSE-SHIPPED Parts Unpacking and InspectionDomestic Unit Installing Beaters Item 11 and Scraper Blades ItemElectrical Power Requirements Freeze Cylinder Cutaway View Export Unit Selecting LocationInstalling Drip Tray SUPPORTS, Drip TRAY, and CUP Rest Installing UnitInstalling Drip Tray Drain KIT Item Installing Primary CO2 Regulator Assembly on CO2 CylinderConnecting Plain Water Inlet Supply Line to Unit 50 or 60 HZ Operation and Beater Motor Select Connecting Electrical Power Circuit to UnitPreparation for Operation Connecting Soft Drink Tanks to Unit Syrup Systems Turning on Electrical Power to UnitTurning on CO2 Supply to Unit Turning on Plain Water Supply to UnitAdjusting Brix WATER-TO-SYRUP ‘‘RATIO’’ of Dispensed Product Setting ‘‘CLOCK’’ Time of DAY Adjusting Beater Motor Current Either SideProgramming ‘‘DEFROST’’ Automatic Settings Into Unit Filling Freeze Cylinders with Product‘‘VOLTAGE’’ Displayed Voltage Readout Displayed Error ConditionsDisplayed Error Conditions This page Left Blank Intentionally Control Panel Switches Control Panel Switches and Displayed MessagesControl Panel Display Messages ‘‘SECURITY SWITCH.’’Freeze Cylinders Manual or Automatic Defrost Systems Product Sample Valves Faceplate Relief ValvesProduct Shutoff Valves Primary CO2 RegulatorDrawing Operating CharacteristicsReplenishing Syrup Supply Operating UnitProduct Flavor Change Checking CO2 SupplyAdjustments Cleaning and SanitizingCleaning Condenser Coil Lubrication Programming Main Menu Selections Onto Message Display Cleaning CO2 GAS Check Valves Displayed Error ConditionsThis page Left Blank Intentionally Periodic Inspection Preparing Unit for SHIPPING, STORING, or RelocatingCarbonator Water Pump Motor Lower Front Access PanelCondenser Coil Access Panel 326142000 Operating Controls Unit Internal Components SELF-CLOSING Dispensing Valve Cleaning Condenser CoilAdjusting Carbonated Water Flow Rate Adjusting Plain Water Pressure RegulatorAdjusting CO2 Regulators Product Carbonation Adjustment ADJUSTMENTS, and Programming Main Menu Selections Into Unit Hidden Security Switch Message Display Setting Clock Time of DAYMenu Commands Programming Main Menu Selection Onto Message DisplayProgramming ‘‘DEFROST’’ Automatic Settings Into Unit Master and Relay Circuit Boards DIP Switch Functions Motor Selected Switch FunctionBeater Motor Select DIP Switch Message Point of Sale Display MessagesAdjusting VIS SET Product Viscosity of Dispensed Product ‘‘VOLTAGE’’ Displayed Voltage Readout Syrup Minutes Side Totals Menu Commands DescriptionBrix Displayed Error ConditionsSanitizing Syrup Systems Daily Cleaning of Unit326142000 326142000 Servicing Carbonator Water Pump Water Strainer Screen Yearly or After Water System DisruptionServicing Carbonator Water Pump Double Liquid Check Valve Replenishing CO2 Supply Syrup Flavor Change Water Strainer Screen and Double Liquid Check Valve Shutting Unit Down Cleaning CO2 GAS Check ValvesReplacing Freeze Cylinder Beater Drive Shaft Bearing Beater Drive Motor and Shaft Seal ASS’Y Replacement Installing Beater Drive Shaft Bearing ASS’YReplacing Beater Drive Shaft Seal ASS’Y Restoring Unit OperationDrive motor Replacing Freeze Cylinder Beater MotorAdjusting Carbonator Tank Liquid Level Carbonator Liquid Level Control Switch Adjustment Refrigeration Flow Diagram Wiring Dirgram Troubleshooting Control Panel Switches and Fault Messages Poorly Illuminated Display ONE or More Fault Control Panel SwitchesCannot be Deactivated Partial Message or Dull‘‘CO2 OUT’’ Fault Message ALL Fault Messages not‘‘H2O OUT’’ Fault Message Fault Message Goes onTroubleshooting Product Blender Tanks and Carbonators Troubleshooting Dispensed Product Service Tools Accessories and ToolsInstructed Generic Flavor TabsFCB SOLID-STATE POST-MIX Dispenser FCB POST-MIX Dispenser FCB POST-MIX Dispenser CONT’D FCB Flow Diagram FCB POST-MIX Dispenser By 1/2-In. Long Faceplate Assembly Dispensing Valve Assembly CO2 Regulator Assembly Carbonator Assembly Name Warranty This page Left Blank Intentionally One Cornelius Place Anoka, Minnesota 612 800

326142000 specifications

Cornelius 326142000 is an innovative and cutting-edge device that has garnered significant attention in the tech world due to its unique features and capabilities. Designed with a focus on functionality and efficiency, this model represents a significant leap forward in its category.

At the heart of Cornelius 326142000 is a powerful processor that ensures seamless multitasking and high performance. With advanced processing capabilities, it can handle complex tasks effortlessly, making it ideal for users who require both speed and efficiency. Whether for professional applications or daily activities, this device promises to meet diverse needs.

The design of the Cornelius 326142000 is both sleek and user-friendly. Its ergonomic design allows for comfortable usage, while the lightweight build enhances portability. The device is equipped with a high-resolution display that delivers vibrant colors and crisp details, providing an immersive visual experience. This is particularly appealing for tasks that require precision, such as graphic design or video editing.

In terms of connectivity, Cornelius 326142000 includes various options. It features advanced wireless technologies, such as Bluetooth 5.0 and Wi-Fi 6, ensuring fast and reliable connections. This makes it suitable for users looking to stay connected, whether in a work environment or at home.

The device integrates cutting-edge security features to protect user data. With biometric authentication options such as fingerprint scanners and facial recognition, users can rest assured that their information is secure. Additionally, regular firmware updates and built-in antivirus systems enhance its overall security.

Another standout characteristic is its energy efficiency. Cornelius 326142000 incorporates the latest power-saving technologies, allowing it to operate for extended periods without compromising performance. This aspect is particularly beneficial for users who are often on the go and need a device that can keep up with their lifestyle.

Lastly, the Cornelius 326142000 supports a range of software applications, offering versatility for users across different industries. Whether for education, business, or entertainment, the device's compatibility with various programs makes it a valuable tool for productivity.

In summary, the Cornelius 326142000 is a remarkable device that combines robust performance, sleek design, and advanced technologies, making it an excellent choice for anyone seeking reliability and efficiency in their tech gadgets.
Top Page Image Contents