Franklin Industries, L.L.C fim35 user manual Installation Types, Mobile Installation

Page 14

IMPORTANT:

•Drain the melt water regularly or you will risk a high rate of melting in the ice storage bin if the water level reaches the ice.

•The unit drains condensation water to the drainage tray on top of the compressor. (See Figure B at bottom of page 12.) This water is slowly evaporated by the heat generated by the compressor. If the drainage tray on top of the compressor becomes full of water, this is detected by the Water Full Probe and the machine shuts off automatically. At the same time, the ice maker sends out an alarm signal and the red, green and yellow LEDs on the Control Panel at the back of the unit flash together. Once the excess water is drained through the drainage nut at the bottom of the ice maker, the machine will start working again automatically.

Installation Types

This ice maker has been designed for Mobile (free-standing) installation. It can also be Enclosed (as under a cabinet) or Built-in (sealed to the floor). In every case, there must be adequate air space around the unit for ventilation purposes (see diagrams on page 8).

Mobile Installation:

A mobile installation will allow you to install the ice maker free-standing in any place you desire provided you have access to a water supply. You must follow the stated instructions for

a. Electrical requirements b. Water supply

c. Leveling the ice maker.

There are four stability supports included with the unit. For mobile installation, these supports, which are located on the bottom of the ice maker, should be turned so that two supports extend out from each side of the unit. (See figure.) The supports add stability to the ice maker.

To secure the stability supports in position: Inside the unit you will find a packet containing four L-shaped brackets and eight screws. One bracket and two screws will be used to secure each stability support and

keep it from rotating out of position. You should attach them as follows:

1.Once the stability supports have been turned outward, adjust the bolt under each support and also the casters under the cabinet until the unit is stable and level.

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Franklin Industries, LLC Table of Contents ICE Maker Safety Important Safeguards Page Extension Cord Technical InformationElectrical Connection ModelIntroduction Component LocationsRemove packaging materials Ice Maker InstallationUnpacking Cleaning before use Location RequirementsElectrical Requirements Electrical Shock HazardLeveling the Ice Maker Recommended grounding methodTo replace door on hinges Reversing the Door SwingTo remove door from hinges Connecting the water line Water SupplyInstallation Types Mobile InstallationEnclosed Installation Built-in InstallationOperating Method OperationFinal Check List before Operation How the Machine Makes Ice How to adjust the capacity of the ice storage bin How the machine uses waterNormal Sounds Preparing the Ice Maker for Long StorageWhat should be kept clean Cleaning and MaintenanceExterior Cleaning What shouldn’t be doneInterior Cleaning Condenser CleaningWater Distribution Tube Cleaning Ice-Making System CleaningPage Control Panel rear of unit Descriptions of LEDs and buttonsMajor Functions Before Calling for Service Problem Possible Cause Probable CorrectionCheck if the water supply pressure is Limited Warranty Franklin Industries, LLCÍndice PáginaSímbolos DE Seguridad Advertencias DE Seguridad Page Conexión eléctrica Cordón prolongadorInformación técnica Introducción Ubicación de componentes de la máquinaQuitar los materiales de embalaje Instalación de la máquinaDesembalaje Requisitos del lugar de instalación Limpieza antes de poner en servicio la máquinaRequisitos de alimentación eléctrica Peligro de electrocuciónNivelación de la máquina Circuito de descarga a tierraPara reemplazar la puerta en las bisagras Cambio del lado de apertura de la puertaPara quitar la puerta de las bisagras Conexiones de entrada de agua Conexión de la línea de aguaTipos de instalación Instalación libreInstalación en cerramiento Instalación empotradaUso de la máquina Lista de control final antes de la puesta en servicioMétodo de uso ImportanteCiclos de funcionamiento de la máquina El circuito de agua en la máquinaCómo ajustar la capacidad del recipiente de hielo Sonidos normalesPreparación de la máquina para almacenamiento prolongado Hay 5 cosas que se deben mantener siempre limpias Limpieza y mantenimientoLo que no se debe hacer Limpieza externa Limpieza internaLimpieza del condensador Limpieza del tubo de distribución de aguaLimpieza del sistema para hacer hielo Descripción de luces LED y botones Tablero de control detrás de la unidadFunciones principales Antes de llamar al servicio de reparación Problema Posible causa Solución probableDiagnóstico de fallas Problema Posible causa Solución probable Garantía limitada Franklin Industries, LLCTable des matières Sécurité de l’appareil Sauvegarder ces instructionsPrécautions Importantes Sauvegarder CES Instructions Câble de rallonge Informations techniquesBranchement électrique ModèlePositions des composants Enlever les matériaux d’emballage Installation de l’appareilDéballage Spécifications pour l’emplacement Nettoyage avant l’emploiSpécifications électriques Risque d’électrocutionMéthode de mise à la terre recommandée Mise à niveau de l’appareil pour la fabrication des glaçonsPour remplacer la porte sur les gonds Pour inverser l’ouverture de la portePour enlever la porte des gonds Branchement de l’alimentation d’eau Branchement de l’alimentation d’eauTypes d’installation Installation mobileInstallation enfermée Installation incorporéeFonctionnement Check-list finale avant la mise en serviceMode opératoire Stade de fabrication Procédé de fabrication de la glace Utilisation de l’eau dans la machineBruits qui indiquent un fonctionnement normal Ce qui doit être gardé propre Entretien et NettoyageCe qu’il ne faudrait pas faire Nettoyage du condenseur Nettoyage extérieurNettoyage intérieur Nettoyage du tube pour la distribution d’eau Nettoyage du système de fabrication de la glacePage Instructions pour les diodes LED et les boutons Tableau de contrôle à l’arriére de la unitéFonctions principales Guide à la solution des problèmes Solution des problèmesAvant d’appeler le service d’entretien Problème Cause possible Remède probableProblème Cause possible Remède probable Garantie limitée FIM35-OM-ESF-2 Patent Pending

fim35 specifications

Franklin Industries, L.L.C., known for its innovative approaches in the manufacturing sector, has established itself as a leader in providing high-quality industrial solutions. The company focuses on delivering products that cater to a diverse range of industries, including construction, automotive, and energy, making it a versatile player in the market.

One of the main features of Franklin Industries is its commitment to using advanced technologies in its manufacturing processes. The company employs state-of-the-art machinery and automation systems that enhance production efficiency and accuracy. This technology integration allows Franklin Industries to maintain consistent quality while meeting the growing demands of various sectors.

In addition to manufacturing capabilities, Franklin Industries prioritizes research and development. The company invests significantly in R&D to create innovative products that incorporate the latest advancements in material science and engineering. This dedication to innovation has led to the development of unique product lines featuring eco-friendly materials, thus supporting sustainable practices within the industry.

Franklin Industries also prides itself on its comprehensive quality control standards. Each product undergoes rigorous testing and inspection to ensure it meets the highest benchmarks for safety and performance. This meticulous attention to quality has helped the company build a strong reputation for reliability and durability among its customers.

Another characteristic of Franklin Industries is its customer-centric approach. The company emphasizes building long-term relationships with clients by understanding their needs and providing tailored solutions. This adaptability has allowed Franklin Industries to stand out in an increasingly competitive market, as customers appreciate the flexibility and responsive service the company offers.

Furthermore, Franklin Industries has adopted a proactive stance towards workforce development. The company ensures its employees receive ongoing training and education, keeping them up to date with the latest industry trends and technological advancements. This investment in human capital is crucial for fostering a culture of innovation and excellence within the organization.

In summary, Franklin Industries, L.L.C. exemplifies a forward-thinking manufacturer that combines advanced technology, research-driven innovation, stringent quality control, customer-focused solutions, and a commitment to workforce development. These features and characteristics underscore its position as a leading player in the industrial sector, continually striving to meet the evolving needs of its diverse clientele.
Top Page Image Contents