Franklin Industries, L.L.C Troubleshooting Your Franklin Ice Maker - Tips from Franklin Industries, LLC
Page 26

Troubleshooting

Before Calling for Service

If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the problem persists, check the Troubleshooting Guide below and on the following page. The problem could be something very simple that can be solved without a service call.

Troubleshooting Guide

Problem

Possible Cause

Probable Correction

 

The ice maker is unplugged.

Plug the ice maker in.

 

 

Replace fuse. If it happens again, call

 

The fuse is blown.

for service to check for a short circuit

 

 

in the ice maker.

The machine

The ice maker power

Turn the ice maker power switch to

doesn’t operate.

switch is OFF.

ICE (ON).

 

The ice storage bin is full of

Remove some ice; make sure the

 

ice.

ice-full probe is free of ice.

 

The drainage tray on top of

Drain off water by unscrewing lower

 

the compressor is full.

drainage nut.

The water doesn’t

The water supply tap is

Turn on the water supply tap.

turned off.

feed in after the ice

 

The water supply line is not

 

maker starts.

Reconnect the water supply line.

 

connected properly.

 

 

Condenser may be dirty.

Clean the condenser.

Machine makes

The air flow to the ice

Check the installation.

maker may be obstructed.

ice, but ice storage

 

The ambient temperature

 

bin does not fill up

 

with ice.

and water temperature are

Check the installation.

 

high, or machine is near

 

 

 

some heat source.

 

 

A few water drops fall to

Normal condensation on the door or

 

the floor when you open the

Water is leaking

some water together with ice. Take

door to take out ice from

care when you take out ice.

from the unit.

the ice storage bin.

 

 

Water supply connection

Tighten fitting. See “Connecting the

 

leaking.

Water Line”.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Franklin Industries, LLC Table of Contents ICE Maker Safety Important Safeguards Page Extension Cord Technical InformationElectrical Connection ModelIntroduction Component LocationsRemove packaging materials Ice Maker InstallationUnpacking Cleaning before use Location RequirementsElectrical Requirements Electrical Shock HazardLeveling the Ice Maker Recommended grounding methodTo replace door on hinges Reversing the Door SwingTo remove door from hinges Connecting the water line Water SupplyInstallation Types Mobile InstallationEnclosed Installation Built-in InstallationOperating Method OperationFinal Check List before Operation How the Machine Makes Ice How to adjust the capacity of the ice storage bin How the machine uses waterNormal Sounds Preparing the Ice Maker for Long StorageWhat should be kept clean Cleaning and MaintenanceExterior Cleaning What shouldn’t be doneInterior Cleaning Condenser CleaningWater Distribution Tube Cleaning Ice-Making System CleaningPage Control Panel rear of unit Descriptions of LEDs and buttonsMajor Functions Before Calling for Service Problem Possible Cause Probable CorrectionCheck if the water supply pressure is Limited Warranty Franklin Industries, LLCÍndice PáginaSímbolos DE Seguridad Advertencias DE Seguridad Page Conexión eléctrica Cordón prolongadorInformación técnica Introducción Ubicación de componentes de la máquinaQuitar los materiales de embalaje Instalación de la máquinaDesembalaje Requisitos del lugar de instalación Limpieza antes de poner en servicio la máquinaRequisitos de alimentación eléctrica Peligro de electrocuciónNivelación de la máquina Circuito de descarga a tierraPara reemplazar la puerta en las bisagras Cambio del lado de apertura de la puertaPara quitar la puerta de las bisagras Conexiones de entrada de agua Conexión de la línea de aguaTipos de instalación Instalación libreInstalación en cerramiento Instalación empotradaUso de la máquina Lista de control final antes de la puesta en servicioMétodo de uso ImportanteCiclos de funcionamiento de la máquina El circuito de agua en la máquinaCómo ajustar la capacidad del recipiente de hielo Sonidos normalesPreparación de la máquina para almacenamiento prolongado Hay 5 cosas que se deben mantener siempre limpias Limpieza y mantenimientoLo que no se debe hacer Limpieza externa Limpieza internaLimpieza del condensador Limpieza del tubo de distribución de aguaLimpieza del sistema para hacer hielo Descripción de luces LED y botones Tablero de control detrás de la unidadFunciones principales Antes de llamar al servicio de reparación Problema Posible causa Solución probableDiagnóstico de fallas Problema Posible causa Solución probable Garantía limitada Franklin Industries, LLCTable des matières Sécurité de l’appareil Sauvegarder ces instructionsPrécautions Importantes Sauvegarder CES Instructions Câble de rallonge Informations techniquesBranchement électrique ModèlePositions des composants Enlever les matériaux d’emballage Installation de l’appareilDéballage Spécifications pour l’emplacement Nettoyage avant l’emploiSpécifications électriques Risque d’électrocutionMéthode de mise à la terre recommandée Mise à niveau de l’appareil pour la fabrication des glaçonsPour remplacer la porte sur les gonds Pour inverser l’ouverture de la portePour enlever la porte des gonds Branchement de l’alimentation d’eau Branchement de l’alimentation d’eauTypes d’installation Installation mobileInstallation enfermée Installation incorporéeFonctionnement Check-list finale avant la mise en serviceMode opératoire Stade de fabrication Procédé de fabrication de la glace Utilisation de l’eau dans la machineBruits qui indiquent un fonctionnement normal Ce qui doit être gardé propre Entretien et NettoyageCe qu’il ne faudrait pas faire Nettoyage du condenseur Nettoyage extérieurNettoyage intérieur Nettoyage du tube pour la distribution d’eau Nettoyage du système de fabrication de la glacePage Instructions pour les diodes LED et les boutons Tableau de contrôle à l’arriére de la unitéFonctions principales Guide à la solution des problèmes Solution des problèmesAvant d’appeler le service d’entretien Problème Cause possible Remède probableProblème Cause possible Remède probable Garantie limitée FIM35-OM-ESF-2 Patent Pending

fim35 specifications

Franklin Industries, L.L.C., known for its innovative approaches in the manufacturing sector, has established itself as a leader in providing high-quality industrial solutions. The company focuses on delivering products that cater to a diverse range of industries, including construction, automotive, and energy, making it a versatile player in the market.

One of the main features of Franklin Industries is its commitment to using advanced technologies in its manufacturing processes. The company employs state-of-the-art machinery and automation systems that enhance production efficiency and accuracy. This technology integration allows Franklin Industries to maintain consistent quality while meeting the growing demands of various sectors.

In addition to manufacturing capabilities, Franklin Industries prioritizes research and development. The company invests significantly in R&D to create innovative products that incorporate the latest advancements in material science and engineering. This dedication to innovation has led to the development of unique product lines featuring eco-friendly materials, thus supporting sustainable practices within the industry.

Franklin Industries also prides itself on its comprehensive quality control standards. Each product undergoes rigorous testing and inspection to ensure it meets the highest benchmarks for safety and performance. This meticulous attention to quality has helped the company build a strong reputation for reliability and durability among its customers.

Another characteristic of Franklin Industries is its customer-centric approach. The company emphasizes building long-term relationships with clients by understanding their needs and providing tailored solutions. This adaptability has allowed Franklin Industries to stand out in an increasingly competitive market, as customers appreciate the flexibility and responsive service the company offers.

Furthermore, Franklin Industries has adopted a proactive stance towards workforce development. The company ensures its employees receive ongoing training and education, keeping them up to date with the latest industry trends and technological advancements. This investment in human capital is crucial for fostering a culture of innovation and excellence within the organization.

In summary, Franklin Industries, L.L.C. exemplifies a forward-thinking manufacturer that combines advanced technology, research-driven innovation, stringent quality control, customer-focused solutions, and a commitment to workforce development. These features and characteristics underscore its position as a leading player in the industrial sector, continually striving to meet the evolving needs of its diverse clientele.
Top Page Image Contents