Hearth and Home Technologies 6000BE owner manual + V 1 FT + H 1 FT

Page 20

 

VENTING WITH THREE (3) 90° ELBOWS

 

 

 

V (FT.)

H (FT.)

1' MIN. (305mm)

5' MAX. (1.52m)

2' MIN. (610mm)

10' MAX. (3.1m)

3' MIN. (914mm)

15' MAX. (4.65m)

4' MIN. (1.22m)

20' MAX. (6.2m)

NOTE: H + H1 = 20' MAX. (6.2m)

V + V1 + H + H1= 40' MAX. (12.4m)

H1

V1

V

H

V1

H1

V

H

V + V1 (FT.)

H

+ H1 (FT.)

1' MIN. (305mm)

5'

MAX. (1.52m)

2' MIN. (610mm)

10'

MAX. (3.1m)

3' MIN. (914mm)

15'

MAX. (4.65m)

4' MIN. (1.22m)

20'

MAX. (6.2m)

H +H1 = 20' MAX. (6.2m)

NOTE: V+V1+H +H1 = 40' MAX. (12.4m)

Figure 17. Venting with three 90° elbows

20

Hearth & Home Technologies • 6000BE, 6000BE-IPI2024-900 Rev. G • 11/05

Image 20
Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Log Set AssemblyService Parts List 6000BE, 6000BE-IPI GLA-750TRValve Assembly Intermittent Pilot Ignition6000BE Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Hearth & Home Technologies Gas Fireplaces Diagram of the 6000BE, 6000BE-IPI GAS Line AccessClearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing Dimensions Framing the FireplaceDVP90ST Installing the Vent System Vent System ApprovalsTems or Components MAY be Used Identifying Vent ComponentsMAX .4 M Straight Up Vertical Venting Flue Restrictor InstructionsVertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Horizontal Termination Vent TerminationAttic Firestop Service Alcove ApplicationsPositioning, Leveling, and Securing the Fireplace Proper Positioning Leveling and Securing of a FireplaceInstalling the Optional Heat-Zone Kit Gas Control Systems Vice Must be Wired Directly to the FIRE- Place Junction BOXStanding Pilot Ignition System Intermittent Pilot Ignition IPI SystemGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Check for GAS LeaksWiring the Fireplace For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchOperation using Battery Power BRNFinishing Installing Trim, Logs, and Ember MaterialInstalling the Trim Follow these steps Positioning the LogsShutter Settings Cover Ports6000BE Tempered 6000BE-IPI Tempered Glass AssemblyPlacing the Ember Material Before Lighting the Fireplace Double-check for faulty componentsCold Climate Switch After the Installation Fireplace MaintenanceLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace