Hearth and Home Technologies 6000BE Vent Termination, Attic Firestop, Horizontal Termination

Page 24

NOTE: There must be NO INSULATION or other combustibles inside the framed firestop opening.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 26. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm).

	NAILS (4 REQUIRED)
	RAFTER
CEILING
	CEILING FIRESTOP
Figure 27.	Attic Firestop

C. Vent Termination

Refer to Cinch Pipe and Termination Cap installation in- structions.

Horizontal Termination

•The termination kit should pass through the wall firestops from the exterior of the building.

•Adjust the termination cap to its final exterior position on the building and interlock the flue sections.

WARNING: THE TERMINATION CAP MUST BE

!POSITIONED SO THAT THE ARROW IS POINT- ING UP.

!WARNING: VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SID-

ING. VENT TERMINATION CLEARANCES MUST BE FOLLOWED TO AVOID FIRE DANGER. SEE VENT TERMINATION MINIMUM CLEARANCES DI- AGRAM ON FOLLOWING PAGE.

7 1/4”

(184mm)

Figure 28. Trapezoid Termination Cap

24	Hearth & Home Technologies • 6000BE, 6000BE-IPI • 2024-900 Rev. G • 11/05

Image 24

Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Log Set AssemblyService Parts List 6000BE, 6000BE-IPI GLA-750TRValve Assembly Intermittent Pilot Ignition6000BE Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationPre-install Preparation Introducing the Hearth & Home Technologies Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000BE, 6000BE-IPI GAS Line AccessConstructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing Dimensions Framing the FireplaceDVP90ST Installing the Vent System Vent System ApprovalsTems or Components MAY be Used Identifying Vent ComponentsFlue Restrictor Instructions Vertical VentingMAX .4 M Straight Up Vertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Vent Termination Attic FirestopHorizontal Termination Service Alcove ApplicationsPositioning, Leveling, and Securing the Fireplace Proper Positioning Leveling and Securing of a FireplaceInstalling the Optional Heat-Zone Kit Gas Control Systems Vice Must be Wired Directly to the FIRE- Place Junction BOXStanding Pilot Ignition System Intermittent Pilot Ignition IPI SystemGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Check for GAS LeaksWiring the Fireplace For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchOperation using Battery Power BRNInstalling Trim, Logs, and Ember Material Installing the TrimFinishing Follow these steps Positioning the LogsShutter Settings Cover PortsGlass Assembly Placing the Ember Material6000BE Tempered 6000BE-IPI Tempered Double-check for faulty components Cold Climate SwitchBefore Lighting the Fireplace After the Installation Fireplace MaintenanceLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace