Hearth and Home Technologies owner manual Diagram of the 6000BE, 6000BE-IPI, GAS Line Access

Page 10

				28 1/2 [724mm]
		14 1/4
		[362mm]
					21 1/2 [548mm]
		8 [203mm]		11 5/8 [297mm]
		VENT COLLARS		11 5/8 [297mm]		8
		VENT COLLARS			ELECTRICAL	8
					ELECTRICAL	[203mm]
					ACCESS	[203mm]
					ACCESS	VENT
						COLLARS
		GAS LINE
		ACCESS
		38		25 1/4	34 5/8
		[965mm]		25 1/4	[879mm]
		[965mm]		[642mm]	[879mm]
				[642mm]
		2 1/8			3 1/2	26 7/8
		[55mm]			[90mm]	[682mm]
				36 1/8
				[916mm]
						12 3/4
		6 7/8 [174mm]	41			[323mm]
			[1040mm]
			TOP STANDOFFS	TOP VENT COLLARS
			REAR VENT COLLARS
			HOOD
			TRIM
			DOOR
			RATING PLATE
	GAS		AND LABELS
	GAS
	LINE
	ACCESS	GAS		ELECTRICAL
		CONTROLS		ACCESS
Î	Figure 1.	Diagram of the 6000BE, 6000BE-IPI
	10	Hearth & Home Technologies • 6000BE, 6000BE-IPI • 2024-900 Rev. G • 11/05

Image 10

Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Log Set AssemblyService Parts List 6000BE, 6000BE-IPI GLA-750TRValve Assembly Intermittent Pilot Ignition6000BE Standing Pilot IgnitionAppliance Certification High Altitude InstallationsInstallation Codes CertificationIntroducing the Hearth & Home Technologies Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000BE, 6000BE-IPI GAS Line AccessLocating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing Dimensions Framing the FireplaceDVP90ST Tems or Components MAY be Used Installing the Vent SystemVent System Approvals Identifying Vent ComponentsVertical Venting Flue Restrictor InstructionsMAX .4 M Straight Up Vertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components Continue Adding Vent Components To Install the Heat ShieldInstall Support Brackets Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Attic Firestop Vent TerminationHorizontal Termination Service Alcove ApplicationsPositioning, Leveling, and Securing the Fireplace Proper Positioning Leveling and Securing of a FireplaceStanding Pilot Ignition System Installing the Optional Heat-Zone Kit Gas Control SystemsVice Must be Wired Directly to the FIRE- Place Junction BOX Intermittent Pilot Ignition IPI SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Check for GAS LeaksOptional Accessories Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchOperation using Battery Power BRNInstalling the Trim Installing Trim, Logs, and Ember MaterialFinishing Follow these steps Positioning the LogsShutter Settings Cover PortsPlacing the Ember Material Glass Assembly6000BE Tempered 6000BE-IPI Tempered Cold Climate Switch Double-check for faulty componentsBefore Lighting the Fireplace Lighting the Fireplace After the InstallationFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace

GAS LINE

ACCESS

Diagram of the 6000BE, 6000BE-IPI