Hearth and Home Technologies 6000BE owner manual Framing the Fireplace, Framing Dimensions

Page 12

Step 2. Framing the Fireplace

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommo- date wall coverings and fireplace facing material. The dia- gram below shows framing reference dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING.

Shows center of 10” x 12” vent framing holes for top and rear venting. The center of the hole is one (1) inch (25.4mm) above the center of the horizontal vent pipe.

B

A.	.............	42”*
B.	......... 38	1/2”
C.	...............	22”
D.	......... 42	3/4”
E.	......... 27	7/8”

Framing should be constructed of 2 X 4 lumber or heavier.

E	D	C

A

1/2” CLEARANCE FROM BACK OF FIREPLACE TO COMBUSTIBLE

1/2” CLEARANCE FROM BOTH SIDES OF FIREPLACE TO COMBUSTIBLE

FRAMING

MEMBER

0” CLEARANCE	0” CLEARANCE TO
	FRAMING MEMBER

Figure 3. Framing Dimensions

12	Hearth & Home Technologies • 6000BE, 6000BE-IPI • 2024-900 Rev. G • 11/05

Image 12

Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Log Set AssemblyService Parts List 6000BE, 6000BE-IPI GLA-750TRValve Assembly Intermittent Pilot Ignition6000BE Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationPre-install Preparation Introducing the Hearth & Home Technologies Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000BE, 6000BE-IPI GAS Line AccessConstructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing Dimensions Framing the FireplaceDVP90ST Installing the Vent System Vent System ApprovalsTems or Components MAY be Used Identifying Vent ComponentsFlue Restrictor Instructions Vertical VentingMAX .4 M Straight Up Vertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Vent Termination Attic FirestopHorizontal Termination Service Alcove ApplicationsPositioning, Leveling, and Securing the Fireplace Proper Positioning Leveling and Securing of a FireplaceInstalling the Optional Heat-Zone Kit Gas Control Systems Vice Must be Wired Directly to the FIRE- Place Junction BOXStanding Pilot Ignition System Intermittent Pilot Ignition IPI SystemGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Check for GAS LeaksWiring the Fireplace For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchOperation using Battery Power BRNInstalling Trim, Logs, and Ember Material Installing the TrimFinishing Follow these steps Positioning the LogsShutter Settings Cover PortsGlass Assembly Placing the Ember Material6000BE Tempered 6000BE-IPI Tempered Double-check for faulty components Cold Climate SwitchBefore Lighting the Fireplace After the Installation Fireplace MaintenanceLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace