Hearth and Home Technologies 6000BE Venting with ONE 1 90 Elbow, Venting with One 90 Elbow

Page 17

VENTING WITH ONE (1) 90° ELBOW

V		H
1' MIN. (305mm)	2'	MAX. (610mm)
2' MIN. (610mm)	4'	MAX.	(1.22m)
3' MIN. (914mm)	6'	MAX.	(1.86m)
4' MIN. (1.22m)	8'	MAX.	(2.4m)
V+H=40' MAX. (12.4m)	H = 8' MAX. (2.4m)

NOTE: On vertical venting configurations, where the vertical component is over 10 feet, install the flue restrictor included in the manual bag assembly to improve flame appearance.

Figure 12. Venting with One 90° Elbow

V

H

VENTING WITH ONE (1) 90° ELBOW

V (FT.)	H (FT.)
1' MIN. (305mm)	5' MAX. (1.52m)
2' MIN. (610mm)	10' MAX. (3.1m)
3' MIN. (914mm)	15' MAX. (4.65m)
4' MIN. (1.22m)	20' MAX. (6.2m)

V+H= 40’ MAX. (12.4MM) H = 20' MAX. (6.2m)

H

V

H

V

NOTE: For corner installations: A 6-inch (152mm) section of straight pipe may need to be attached to the fireplace before a 90o elbow, to allow the vent pipe to clear the top standoffs.

Figure 13. Venting with One 90° Elbow

NOTE: If a 90o elbow is first attached to the unit, the maximum horizontal run is 3-feet (914mm).

Hearth & Home Technologies • 6000BE, 6000BE-IPI • 2024-900 Rev. G • 11/05

17

Image 17

Contents What to do if you smell gas Installation and OperationSafety and Warning Information Table of Contents Log Set Assembly Service PartsGLA-750TR Service Parts List 6000BE, 6000BE-IPIIntermittent Pilot Ignition Valve AssemblyStanding Pilot Ignition 6000BEInstallation Codes High Altitude InstallationsAppliance Certification CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Hearth & Home Technologies Gas Fireplaces GAS Line Access Diagram of the 6000BE, 6000BE-IPIClearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing the Fireplace Framing DimensionsDVP90ST Vent System Approvals Installing the Vent SystemTems or Components MAY be Used Identifying Vent ComponentsMAX .4 M Straight Up Vertical Venting Flue Restrictor InstructionsVertical Venting Chart Venting with One 90 Elbow Venting with ONE 1 90 ElbowVenting with Two 90 Elbows Venting with TWO 2 90 o ElbowsVenting with three 90 elbows Venting with Three 3 90 Elbows+ V 1 FT + H 1 FT Installing Vent Components Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Horizontal Termination Vent TerminationAttic Firestop Alcove Applications ServiceProper Positioning Leveling and Securing of a Fireplace Positioning, Leveling, and Securing the FireplaceVice Must be Wired Directly to the FIRE- Place Junction BOX Installing the Optional Heat-Zone Kit Gas Control SystemsStanding Pilot Ignition System Intermittent Pilot Ignition IPI SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Check for GAS LeaksFor Standing Pilot Ignition Wiring Appliance Requirements Wiring the FireplaceOptional Accessories Wall SwitchBRN Operation using Battery PowerFinishing Installing Trim, Logs, and Ember MaterialInstalling the Trim Positioning the Logs Follow these stepsCover Ports Shutter Settings6000BE Tempered 6000BE-IPI Tempered Glass AssemblyPlacing the Ember Material Before Lighting the Fireplace Double-check for faulty componentsCold Climate Switch Fireplace Maintenance After the InstallationLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace