GE 164D3333P172 owner manual Power Cord Strain Relief Installation

Page 31

3 Power Cord Strain Relief Installation

	Remove the lower rear range wiring cover to expose the connector block and
a
	bracket.
	Remove the knockout ring (13⁄8″) located on bracket directly below the
b
	connector. To remove the knockout, use a pair of pliers to bend the
	knockout ring away from the bracket and twist until ring is removed.

	Knockout ring in bracket.	Knockout ring removed.
	Assemble the strain relief in the hole. Insert the power cord through the
c
	strain relief and tighten. Allow enough slack to easily attach the cord
	terminals to the connector block. If tabs are present at the end of the winged
	strain relief, they can be removed for better fit.
	NOTE: Do not install the power cord without a strain relief. The strain relief bracket should
	be installed before reinstalling the rear range wiring cover.

	Connector box
				Ground
				strap

Wiring cover								Bracket
(shown removed)


	Strain relief		Power cord					Strain relief bracket
								(Provided with range cord. Not part of range.)
								(Provided with range cord. Not part of range.)

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

31

Image 31

Contents GE Answer Center GE AppliancesCongratulations You Are Now Part of the GE Family Staple sales slip or cancelled check hereWrite the model and serial numbers here GE & You Service Partnership Cycle. Exposure can be minimized by venting with an open Fiberglass insulation in self-clean ovens gives off a veryAll ranges can tip and injury could result California Safe Drinking Water and Toxic EnforcementSafety Precautions Safety Information Oven SELF-CLEANING Oven Surface Cooking Units REMEMBER… Customer Service Troubleshooting TipsWok Cooking Using the surface unitsHow to Set Surface Cookware TipsCustomer Service Using the oven controlsOven Control Settings Type of margarine will affect baking performance Using the ovenHow to Set the Oven for Baking or Roasting Before you begin…How to Set the Oven for Broiling Preheating and Pan PlacementAluminum Foil Comments Broiling guideUsing the clock and timer Press Cook Time ON/OFF How to Set an Immediate StartAutomatic Stop Make sure the oven clock shows the correct time of dayFor Models with Pads and an Oven Temperature Knob For Models with Only an Oven Temperature KnobBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning After a Clean Cycle How to Delay the Start of CleaningPress the Start Time ON/OFF pad Painted Surfaces Care and cleaning of the rangeControl Panel and Knobs Oven VentDo not lift the door by the handle To clean the inside of the doorTo clean the outside of the door Lift-Off Oven DoorTo remove the cover Oven Light Replacement on some modelsOven Heating Elements Oven ShelvesTo remove the storage drawer Broiler Pan & GridTo replace the storage drawer Lift-Up Cooktop on some models Porcelain Enamel CooktopTo replace a surface unit Surface UnitsDrip Pans To remove a surface unitWiring must conform to National Electric Codes Installation of the rangePrepare the Opening Prepare for Electrical Connection Flooring Under the RangeBe installed before reinstalling the rear range wiring cover Power Cord Strain Relief InstallationDo not remove ground strap connection Wire Power Cord InstallationBefore After Local codes Wire Conduit InstallationConnector block terminal Bare wire Leveling the Range Anti-Tip Bracket InstallationFinal Check Before you call for service… Or roast properly Customer Service Troubleshooting Tips InstallationInstructions Operating Instructions Food does not bakeSelf-clean cycle Oven temperatureClock and timer Self-cleanTo Clean Oven not cleanAfter a clean cycle Clean lightA number Is on when youPower outage Want to cookCustomer Service From the date GE Electric Range WarrantyWe Will Replace, At No Charge To You One YearIn-Home Repair Service 800-GE-CARES Service Telephone NumbersTDD 800-TDD-GEAC