GE 10-95 CG warranty Step Final Check

Page 39

STEP 8

ANTI-TIP BRACKET INSTALLATION

AN ANTI-TIP bracket is supplied with instructions for installation in a variety of locations. The instructions include a template, a parts list and a list of tools necessary to complete the installation. Read the IMPORTANT SAFETY INSTRUCTIONS and the instructions that fit your situation before beginning installation.

WARNING

1.Range must be secured by ANTI-TIP bracket supplied.

2.See instructions to install (supplied with bracket).

3.Unless properly installed, range could be tipped by stepping or sitting on door. Injury might result from spilled hot liquids or from range itself.

Typical Installation of Anti-Tip Bracket

Attachment to Wall

Bracket

 

Screw Must Enter

Wall Plate

Wood or Metal

 

STEP 9

LEVELING THE RANGE

The range must be level. Leveling feet are located at each corner of the base of the range. Remove the storage drawer or kick panel (depending on your model) and using channel locks, rotate the leveling feet in and out as required to level the range. (For instructions on how to remove and replace the storage drawer or the kick panel, see the Cleaning Under the Range section in Care and Cleaning.) On some models, there are plastic covers which may be removed for easy adjustment (just squeeze and pull).

One of the rear leveling feet will engage the ANTI-TIP bracket (allow for some side to side adjustment). Allow a minimum clearance of 1/8- inch between the range and the leveling foot that is to be installed into the ANTI-TIP bracket.

Check the range for proper installation into the ANTI-TIP bracket (after the range has been properly installed) by removing the kick panel or storage drawer and inspecting the rear leveling leg. Make sure it fits securely into the slot.

STEP 10

FINAL CHECK

Be sure all switches are in the OFF position before leaving the range.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents UseandCare& Installation Guide Save time and money. Before you request service… Help US Help YOU…If you received Damaged range… Important Safety Instructions Important Safety InstructionsOven Self-Cleaning OvenCooktop and Radiant Surface Units Save These InstructionsJBP79 Features of Your RangeFeatures of Your Range Type of Cooktop Description How It Works Radiant HOW does this Cooktop Compare To Your OLD ONE?General Information About Radiant Surface Units Cooktop ComparisonSurface Controls How to Set the ControlsDual Surface Unit Switch Cooking Guide for Using Heat SettingsHot Surface Indicator Light Surface ControlsSpecial Notes for Glass Cooktops Porcelain/enamel Surface Cookware TipsTypes of Cookware Copper BottomHow to Check Pan Performance SurfaceResistant, not scratch proof Flat-bottomed canners are required for glass cooktops Home Canning TipsObserve the Following Points in Canning Canning should be done on the cooktop onlyHome Canning Tips Glass Cooktop CleaningCleaning Glass Cooktop CleaningBroil Bake Features of Your Oven ControlOven Control Oven CONTROL, Clock and TimerFeatures of Your Clock and TimerShelf Positions Using Your OvenBefore Using Your Oven Oven ShelvesBaking UsingBaking Your OvenCookies Pan PlacementBaking Pans Baking GuidesDon’t Peek How to Time BakeHow to Set Immediate Start and Automatic Stop Timed BakingQuick Reminder How to Set Delay Start and Automatic StopTimed Baking Adjust the Oven Thermostat Adjust the Oven ThermostatUse of Aluminum Foil RoastingFor Frozen Roasts Questions and AnswersWhy is my roast crumbling when I try to carve it? Roasting GuideWhy are my meats not turning out as brown as they should? BroilingShould I salt the meat before broiling? Broiling Guide BroilingOven door should be open to the broil stop position Before a Clean Cycle Operating the SELF-CLEANING OvenTo Stop a Clean Cycle Cleaning OvenHow to Set the Oven for Cleaning After a Clean CycleHow to Set Delay Start of Cleaning Care and Cleaning Operating the Self-Cleaning OvenCare Glass Window Control Panel and KnobsCooktop Surface Light Metal PartsOven Heating Elements Care and CleaningLift-Off Oven Door Sure Grip HandleAfter broiling, remove How to Remove the Storage Drawer to Clean Under the RangeOven Light Replacement Broiler Pan and GridBefore YOU Begin Installation InstructionsStep Step Wire Power Cord Installation Step Wire Conduit Installation Step Final Check Problem Possible Cause QUESTIONS? USE this Problem SolverAfter Clean Cycle Problem SolverIf YOU Need Service Problem SolverNeed Problem Solver If YouService ServicesWarranty

10-95 CG specifications

The GE 10-95 CG is a notable locomotive designed to meet the demands of freight transport with efficiency and reliability. Built by General Electric, this model showcases a combination of advanced technology and impressive engineering, making it a prominent choice in the rail industry.

One of the primary features of the GE 10-95 CG is its powerful diesel engine. The locomotive is equipped with a 12-cylinder 7FDL engine, capable of producing substantial horsepower that allows it to handle heavy loads across challenging terrains. This engine configuration not only provides reliability but also ensures operational efficiency, allowing for lower fuel consumption over longer distances.

The 10-95 CG is recognized for its distinct, rugged design that is built to withstand diverse environmental conditions. Its robust frame and sturdy body contribute to its longevity and durability, while the optimized aerodynamics reduce drag, enhancing fuel efficiency. The locomotive's structure is designed for easy access and maintenance, allowing operators to keep it in optimal working condition with minimal downtime.

In terms of technologies, the GE 10-95 CG integrates advanced electronic systems that enhance performance and monitoring. The locomotive features a sophisticated microprocessor-based control system that enables precise engine management, ensuring optimal operation under varying conditions. Additionally, the use of dynamic braking technology provides enhanced control, reducing wear and tear on the braking system while improving safety.

The traction system of the GE 10-95 CG employs alternating current (AC) traction motors, which are known for their efficiency and reduced maintenance requirements compared to traditional DC motors. This technology results in better acceleration and overall performance, making the locomotive adept in both hauling heavy freight and navigating tight curves.

Another notable characteristic of the GE 10-95 CG is its ability to operate in multiple unit configurations. This allows for seamless coupling with other locomotives, enabling operators to scale their freight capacity as needed. The versatility of this locomotive makes it a valuable asset in various rail operations.

In summary, the GE 10-95 CG embodies a blend of power, efficiency, and advanced technology. With features designed for durability, operational efficiency, and ease of maintenance, it stands out as a formidable choice for freight transportation in the rail industry. Its innovative systems and robust performance characteristics ensure that it remains a reliable solution for meeting the demands of modern logistics and transportation.
Top Page Image Contents