GE 10-95 CG warranty Surface Controls, How to Set the Controls, Dual Surface Unit Switch

Page 10

SURFACE CONTROLS

At both OFF and HI the control “clicks” into position. You may hear slight “clicking” sounds during cooking, indicating the control is keeping the unit at the heat level or power level you set.

Switching heats to higher settings always shows a quicker change than switching to lower settings.

How to Set the Controls

Push the knob in and turn in either direction to the setting you want.

Be sure you turn the control knob to OFF when you finish cooking.

The surface unit “on” indicator light will glow

when ANY surface unit is on.

Dual Surface Unit Switch

The right front surface unit has 2 cooking sizes to select from so you can match the size of the unit to the size of the cookware you are using.

To use the large (9-inch) surface unit, push in the right portion of the COIL SIZE switch next to the control knob. Push in and turn the control knob to the desired setting.

To use the small (6-inch) surface unit, push in the left portion of the COIL SIZE switch. Push in and turn the control knob to the desired setting.

Light Over the Surface Units

The switch must be pushed, held for several seconds, and released for the light to come on.

SURFACE

LIGHT

Cooking Guide for Using Heat Settings

HI—Used to begin cooking or to bring water to a boil. Reduce heat setting after water boils.

Medium High—(Setting halfway between HI and MED) Maintains a fast boil on large amounts of food.

MED—Sauté and brown; keeps food at a medium boil.

Medium Low—(Setting halfway between MED and LO) Cook after starting at HI; cooks with little water in covered pan.

LO—Used for long slow cooking (simmering) to tenderize and develop flavors. Use this setting to melt butter and chocolate or to keep foods warm.

NOTE: The surface unit “on” indicator light may glow between LO and OFF, but there is no power to the surface units.

Medium

Medium

Low

High

Appearance may vary slightly.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents UseandCare& Installation Guide Help US Help YOU… Save time and money. Before you request service…If you received Damaged range… Important Safety Instructions Important Safety InstructionsSelf-Cleaning Oven OvenSave These Instructions Cooktop and Radiant Surface UnitsFeatures of Your Range JBP79Features of Your Range HOW does this Cooktop Compare To Your OLD ONE? Type of Cooktop Description How It Works RadiantCooktop Comparison General Information About Radiant Surface UnitsCooking Guide for Using Heat Settings How to Set the ControlsDual Surface Unit Switch Surface ControlsSurface Controls Hot Surface Indicator LightSpecial Notes for Glass Cooktops Copper Bottom Surface Cookware TipsTypes of Cookware Porcelain/enamelSurface How to Check Pan PerformanceResistant, not scratch proof Canning should be done on the cooktop only Home Canning TipsObserve the Following Points in Canning Flat-bottomed canners are required for glass cooktopsGlass Cooktop Cleaning Glass Cooktop CleaningCleaning Home Canning TipsFeatures of Your Oven Control Broil BakeClock and Timer Oven CONTROL, Clock and TimerFeatures of Your Oven ControlOven Shelves Using Your OvenBefore Using Your Oven Shelf PositionsYour Oven UsingBaking BakingBaking Guides Pan PlacementBaking Pans CookiesTimed Baking How to Time BakeHow to Set Immediate Start and Automatic Stop Don’t PeekHow to Set Delay Start and Automatic Stop Quick ReminderAdjust the Oven Thermostat Timed Baking Adjust the Oven ThermostatRoasting Use of Aluminum FoilRoasting Guide Questions and AnswersWhy is my roast crumbling when I try to carve it? For Frozen RoastsBroiling Why are my meats not turning out as brown as they should?Should I salt the meat before broiling? Broiling Broiling GuideOven door should be open to the broil stop position Operating the SELF-CLEANING Oven Before a Clean CycleAfter a Clean Cycle Cleaning OvenHow to Set the Oven for Cleaning To Stop a Clean CycleHow to Set Delay Start of Cleaning Operating the Self-Cleaning Oven Care and CleaningCare Metal Parts Control Panel and KnobsCooktop Surface Light Glass WindowSure Grip Handle Care and CleaningLift-Off Oven Door Oven Heating ElementsBroiler Pan and Grid How to Remove the Storage Drawer to Clean Under the RangeOven Light Replacement After broiling, removeInstallation Instructions Before YOU BeginStep Step Wire Power Cord Installation Step Wire Conduit Installation Step Final Check QUESTIONS? USE this Problem Solver Problem Possible CauseProblem Solver After Clean CycleProblem Solver If YOU Need ServiceServices Problem Solver If YouService NeedWarranty

10-95 CG specifications

The GE 10-95 CG is a notable locomotive designed to meet the demands of freight transport with efficiency and reliability. Built by General Electric, this model showcases a combination of advanced technology and impressive engineering, making it a prominent choice in the rail industry.

One of the primary features of the GE 10-95 CG is its powerful diesel engine. The locomotive is equipped with a 12-cylinder 7FDL engine, capable of producing substantial horsepower that allows it to handle heavy loads across challenging terrains. This engine configuration not only provides reliability but also ensures operational efficiency, allowing for lower fuel consumption over longer distances.

The 10-95 CG is recognized for its distinct, rugged design that is built to withstand diverse environmental conditions. Its robust frame and sturdy body contribute to its longevity and durability, while the optimized aerodynamics reduce drag, enhancing fuel efficiency. The locomotive's structure is designed for easy access and maintenance, allowing operators to keep it in optimal working condition with minimal downtime.

In terms of technologies, the GE 10-95 CG integrates advanced electronic systems that enhance performance and monitoring. The locomotive features a sophisticated microprocessor-based control system that enables precise engine management, ensuring optimal operation under varying conditions. Additionally, the use of dynamic braking technology provides enhanced control, reducing wear and tear on the braking system while improving safety.

The traction system of the GE 10-95 CG employs alternating current (AC) traction motors, which are known for their efficiency and reduced maintenance requirements compared to traditional DC motors. This technology results in better acceleration and overall performance, making the locomotive adept in both hauling heavy freight and navigating tight curves.

Another notable characteristic of the GE 10-95 CG is its ability to operate in multiple unit configurations. This allows for seamless coupling with other locomotives, enabling operators to scale their freight capacity as needed. The versatility of this locomotive makes it a valuable asset in various rail operations.

In summary, the GE 10-95 CG embodies a blend of power, efficiency, and advanced technology. With features designed for durability, operational efficiency, and ease of maintenance, it stands out as a formidable choice for freight transportation in the rail industry. Its innovative systems and robust performance characteristics ensure that it remains a reliable solution for meeting the demands of modern logistics and transportation.
Top Page Image Contents