Broan HEPA 3000, HEPA 4000, HEPA 2000, HEPA 1000 installation instructions Parts Ordering Chart

Page 37

7. PARTS ORDERING CHART

 

No. Description

Part

HEPA

1000

HEPA 2000

 

 

Number

HF 1.0

HF 2.0

 

 

 

 

 

 

1

Prefilter Kit (2)

05123

1

 

1

 

 

2

HEPA Pleated Filter Kit

04803

1

 

1

 

 

3

MERV 12 Filter Kit*

04804

1

 

1

 

 

4

Foam Filter MERV 8 Kit*

04852

1

 

1

 

 

5

Core Filter Kit (2)

05120

-

 

-

 

 

6

Single Exterior Hood Kit**

13940

-

 

1

 

 

7

Wall Control C12**

04862

1

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No. Description

Part

HEPA

3000

HEPA 4000

 

 

 

 

Number

HF 3.0

 

 

 

1

Prefilter Kit (2)

05123

1

 

1

 

 

2

HEPA Pleated Filter Kit

04803

1

 

1

 

 

3

MERV 12 Filter Kit*

04804

1

 

1

 

 

4

Foam Filter MERV 8 Kit*

04852

1

 

1

 

 

5A

Core Filter Kit (2)

05120

1

 

-

 

 

5B

Core Filter Kit (2)

05689

-

 

1

 

 

6

Single Exterior Hood Kit**

13940

1

 

1

 

 

7

Wall Control C34**

04391

1

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*The HEPA filter is factory installed in all our units. However, when it will be time to be replaced, a pleated filter or a foam filter can be purchased, but the filtration efficiency will not be the same as a HEPA filter.

**Items 6 and 7 are optionals.

All listed parts are available where you have bought your unit.

NOTE: Please note that parts not listed are not available; those parts require assembly knowledge that only manufacturer can garantee.

- 37 -

Image 37
Contents Installation Instructions About this Manual About These Units Table of Contents Table DES Matières Before Starting Typical InstallationsTypical Installations CONT’D Hepa 1000 and HF 1.0 Unit Installations CONT’D RETURN-RETURN Installation Connection to a Forced AIR System Hepa 4000 Restricted Area VH0051 Hepa 2000, HF 2.0, Hepa 3000, HF 3.0 and Hepa Hepa 2000, HF 2.0, Hepa 3000, HF 3.0 and Hepa 4000 Unit VH0043 Front View TOP View DimensionsDimensions CONT’D Install the Unit Install the Unit CONT’D HOW to Hang the Unit CONT’D Stale air exhaust ductwork Stale air ductwork Filtered air ductwork Return side connection cont’d Hepa 2000, HF2.0, Hepa 3000, HF 3.0 and Hepa 4000 Units only Pull back the insulation to expose the flexible duct 457 mm Xmas tree pin Connecting the Drain Hepa 3000 and HF 3.0 Units only NORMAL/REMOTE ControlsControls C12 / CM and C34 / CMR Controls CONT’DControls C12 / CM and C34 / CMR CONT’D VD0088 Is on Normal or Boost Using C34 / CMR Control Maintenance For Hepa 2000 and HF 2.0 only Maintenance CONT’DMaster Reset C12 / CM and C34 / CMR Controls Parts Ordering Chart Problems Solutions Troubleshooting