321 Studios FH110D48E, FLF110D48E, FLR140D60E, FLF085D36E OIL Line Piping, Beckett AFG OIL Burner

Page 12

OIL LINE PIPING

First determine whether the pipe system is to be a single line system or a two line system. All connections must be absolutely air tight or you will have a malfunction of the burner. When installing the piping, a good oil filter should be installed close to the burner. A single line system is recommended for gravity feed.

A typical single inside tank installations shown in Figure 6. For installation details for this and other tank configurations, refer to NFPA31 -- latest edition. All tank and pipe setups must comply with NFPA31.

BECKETT AFG OIL BURNER

This furnace is equipped with a high static Beckett AFG oil burner which is designed to produce adequate draft in nearly any vertically vented application. The burner employs the latest time tested controls of the highest quality. The controls consist of a high voltage Beckett solid state igniter, a Beckett “CleanCut” oil pump with an integral solenoid valve, and a Beckett R7184B primary control.

FIGURE 6

TYPICAL SINGLE INSIDE TANK INSTALLATION

Vent Cap

2" Cap

2" Fill Pipe

	1-1/4"	Return Line
	Vent Pipe	Return Line
	Vent Pipe
		Guage

Oil

Tank

6"

Legs (either 1-1/4"x10" or 1-1/2"x10" nipples)

Bushing,

2" x 1-1/2" or 1-1/4"

Gate Valve

3/8" x 4" nipple

3/8" x 3/8" Adapter

3/8" O.D. Copper Fuel Tubing

Bushing

Oil Filter

MIS-1823

Manual 2100-422

Page 10

Image 12

Contents OIL Furnace Installation Instructions Contents Getting Other Information and Publications For More INFORMATION, Contact These PublishersEquipment Selection Locating the FurnaceMinimum Clearances Specification Sheet Supply Specification Sheet Specification Sheet FC085 Model DimensionsInstalling the Furnace Installing a Cooling UnitInstruments Required for Proper Setup of the Furnace InstallationWiring Factory WiringField Wiring Electrical DataTypical Unit Setup FLF Unit Shown I m n e y Typical Single Inside Tank Installation OIL Line PipingBeckett AFG OIL Burner Beckett Cleancut OIL Pump Beckett Solid State IgniterBeckett R7184B Primary Control Beckett R7184B Primary Operational Guide Cleaner Connection Electronic Blower ControlBurner Setup and Adjustment Procedures Furnace DataPreparation Steps Combustion Adjustment Steps Combustion DiagnosisShort Form Adjustment Procedure Final ChecksCheck Draft Smoke TestHigh Air Settings Low Bacharach Smoke Number Typical Smoke CO2 Chart with Adjustment RangePressure Gauge Connection to Bleed Port No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees F Recommended START-UP SettingsCorrelation of Percent of CO2, O2 Reserve AIR GUN Assembly Adjustment Removing GUN AssemblyElectrode Adjustments Combustion AIR RequirementsCombustion AIR Boot Assembly Combination AIR Boot AssemblyAppliances Located in Confined Spaces Square Feet Required to Qualify AS Unconfined SpaceALL AIR from Inside Building Minimum Ventilation Openings ALL Ventilation AIR from OutdoorsAppliances Located in Confined Spaces ALL AIR from Outdoors MIS-1338 Louvers and Grilles Venting OptionsThermostat Vertical Venting200 Typical Installation of FR26 FR27 Filter Racks Typical Installation of FR25 Filter KITFilter Sizes for OIL Furnaces Filter Installation LO-BOY Models LO-BOY Models Filter LocationsService Hints LubricationInspect AIR Filter Final Inspection and TestCombination Combustion CHAMBER/BURNER Mounting System Removal of Burner onlyTo Remove Burner only To Remove the Entire Combustion Chamber Mounting SystemRemoval of Entire Combustion Chamber Mounting System Cleaning of the Heat Exchanger Common Causes of TroubleCare of Finish Chart FH085D36E Data Chart FH110D48E DataChart FH110D60E Data Chart FLF/FLR085D36E DataChart FLR140D60E Data Chart FC085D36E DataFH Series Wiring Diagram UnitCond Cond Unit