321 Studios FC085D36E, FLF110D48E, FH110D48E, FLR140D60E, FLF085D36E, FLF110D60E Specification Sheet

Page 5

FLF/FLR 085, 110 AND 140

SPECIFICATION SHEET

		TOP VIEW	J
	RETURN	TOP VIEW	SUPPLY
	RETURN		SUPPLY
	DUCT		DUCT

D

G
F	E
	"FLF" FLUE
REAR FLUE	KNOCKOUT
REAR FLUE
ON "FLR" MODELS	OPTIONAL
	HIGH VOLTAGE
	ENTRANCE

OPTIONAL

LOW VOLTAGE

FIGURE 1

FLF/R MODELS DIMENSIONS

TABLE 2

FLF/R MODELS DIMENSIONS (INCHES)

		Cabinet			Plenum		Flue Conection				Air Filters
		Cabinet			Openings		Flue Conection				Air Filters		1
Model	A	B		C	D x E	D x F	Location	G	H	J	Size		No.
Number	Width	Depth		Height	Supply	Return	Location	Dia.	H	J	Size		Used
FLF085D36E	23	48.125		36.625	22x20	22x14	Front	6	31.625	5.125	16 x 20 x 1		1
FLR085D36E	23	48.125		36.625	22x20	22x14	Rear	6	31.625	5.125	16 x 20 x 1		1
FLF110D48E	23	48.125		40.625	22x20	22x14	Front	6	35.625	5.125	20 x 20 x 1		1
FLF110D60E	23	48.125		40.625	22x20	22x14	Front	6	35.625	5.125	20 x 20 x 1		1
FLR110D48E	23	48.125		40.625	22x20	22x14	Rear	6	35.625	5.125	20 x 20 x 1		1
FLR110D60E	23	48.125		40.625	22x20	22x14	Rear	6	35.625	5.125	20 x 20 x 1		1
FLR140D60E	26	50.250		47.625	25x20	25x16	Rear	6	42.125	- - -	20 x 25 x 1		1

jWashable type filter 1” nom. thickness

"FLF" FLUE KNOCKOUT

A	B

"FLF" FLUE

KNOCKOUT

LOW VOLTAGE

ENTRANCE

H

ENTRANCE

OIL

C	HIGH VOLTAGE
	ENTRANCE

Page	Manual
3	2100-422
	2100-422

ENTRANCE

OPTIONAL

FILTEROIL

DOORENTRANCE

FRESH AIR

KNOCKOUT

LEFT SIDE VIEW

OPTIONAL

OIL ENTRANCE

FRONT VIEW

RIGHT SIDE VIEW

MIS-1815 A

Image 5

Contents OIL Furnace Installation Instructions Contents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsMinimum Clearances Equipment SelectionLocating the Furnace Specification Sheet Supply Specification Sheet FC085 Model Dimensions Specification SheetInstalling a Cooling Unit Installing the FurnaceInstruments Required for Proper Setup of the Furnace InstallationFactory Wiring WiringField Wiring Electrical DataTypical Unit Setup FLF Unit Shown I m n e y Beckett AFG OIL Burner Typical Single Inside Tank InstallationOIL Line Piping Beckett R7184B Primary Control Beckett Cleancut OIL PumpBeckett Solid State Igniter Beckett R7184B Primary Operational Guide Electronic Blower Control Cleaner ConnectionPreparation Steps Burner Setup and Adjustment ProceduresFurnace Data Combustion Diagnosis Combustion Adjustment StepsFinal Checks Short Form Adjustment ProcedureCheck Draft Smoke TestTypical Smoke CO2 Chart with Adjustment Range High Air Settings Low Bacharach Smoke NumberPressure Gauge Connection to Bleed Port Correlation of Percent of CO2, O2 Reserve AIR No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees FRecommended START-UP Settings Removing GUN Assembly GUN Assembly AdjustmentElectrode Adjustments Combustion AIR RequirementsCombination AIR Boot Assembly Combustion AIR Boot AssemblyALL AIR from Inside Building Appliances Located in Confined SpacesSquare Feet Required to Qualify AS Unconfined Space Appliances Located in Confined Spaces ALL AIR from Outdoors Minimum Ventilation OpeningsALL Ventilation AIR from Outdoors MIS-1338 Venting Options Louvers and GrillesThermostat Vertical Venting200 Filter Sizes for OIL Furnaces Typical Installation of FR26 FR27 Filter RacksTypical Installation of FR25 Filter KIT LO-BOY Models Filter Locations Filter Installation LO-BOY ModelsLubrication Service HintsInspect AIR Filter Final Inspection and TestRemoval of Burner only Combination Combustion CHAMBER/BURNER Mounting SystemRemoval of Entire Combustion Chamber Mounting System To Remove Burner onlyTo Remove the Entire Combustion Chamber Mounting System Care of Finish Cleaning of the Heat ExchangerCommon Causes of Trouble Chart FH110D48E Data Chart FH085D36E DataChart FH110D60E Data Chart FLF/FLR085D36E DataChart FC085D36E Data Chart FLR140D60E DataUnit FH Series Wiring DiagramCond Cond Unit