AC Power and Control, Output Connections, Operation

STEREO COMPACT DISC PLAYER RCD-951

Placement

Use common sense when placing the RCD-951 in a cabinet or when stacking other equipment. Make sure that the shelf or cabi- net can support its weight. Do not stack heavy components on top of the RCD-951. Avoid placing the unit where it may be subject to excessive heat such as on top of a large power amplifier or near a heat register. For best performance, avoid placing the unit where it may be subject to vibration, such as near a speaker.

AC Power and Control

AC Power Input 20

Your RCD-951 is configured at the factory for the proper AC volt- age in the country where you purchased it (either 115 volts or 230/ 240 volts. The AC line configuration is noted on a decal on the back panel.

Output Connections

The RCD-951 gives you a choice of two different kinds of output connections — an analog output signal from the built-in D/A con- verter for use with conventional analog audio components and a coax digital output which provides an unprocessed digital data signal for use with outboard D/A converters or digital processors.

Note: To prevent loud noises that neither you nor your speakers will appreciate, make sure the CD player is turned off when you make any signal connections.

Analog Outputs 18

[See Figure 2 for wiring illustration]

A pair of standard RCA jacks supplies an analog output signal from the RCD-951 to the source inputs of an audio preamplifier, in- tegrated amplifier, or receiver.

Note: Should you move your CD player to another country, it may be possible to reconfigure it for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the en- closure of the RCD-951 exposes you to dangerous voltages. Con- sult a qualified service person or the Rotel factory service department for information.

Select high quality audio interconnect cables. Connect the left channel output of the RCD-951 to the left channel source input on the preamplifier or other component. Connect the right output of the RCD-951 to the right channel source input on the preamplifier or other component.

The RCD-951 should be plugged directly into a 2-pin polarized wall outlet or into the switched outlet on another component in your audio system. Do not use an extension cord.

Be sure the power switch on the front panel of the RCD-951 is turned off (in the "out" position). Then, connect the supplied power cord to the AC power receptacle on the rear of the unit and the AC power outlet.

If you are going to be away from home for an extended period of time such as a month-long vacation, it is a sensible precaution to unplug your CD player (as well as other audio and video compo- nents) while you are away.

Digital Output 19

[See Figure 3 for wiring illustration]

If you are using an outboard D/A converter or other digital proces- sor, you will need an unprocessed digital data stream from the RCD-951, taken before the built-in D/A converter. This signal is supplied by the RCD-951’s back-panel digital output jack.

Using a standard 75 ohm coax digital cable, connect the RCD-951’s coax digital output to the coax digital input connector on the outboard D/A converter.

Power Switch 8 and Power Indicator 1

Operation

The power switch is located on the front panel of your CD player. To turn the CD player on, push the switch in. The LED indicator above the switch and the Display will light up, indicating that the CD player is turned on. To turn the CD player off, push the button again and return it to the "out" position.

Note: If you are using a switched outlet to turn on and off your CD player, you should leave the power switch in the "on" position. When AC power is applied to the unit, it will power up in fully ac- tive mode.

The RCD-951 can be operated using its front panel buttons or from corresponding buttons on the supplied infrared remote control. Specific instructions for each of these controls are detailed be- low. Most of the buttons are duplicated on the front panel and on the IR remote control. However, there are a few exceptions where the buttons are only available on one or the other. These excep- tions are noted in the instructions.

RCD-951 specifications

The Rotel RCD-951 is an exceptional CD player that exemplifies the brand's dedication to high-quality audio reproduction and meticulous engineering. This player is designed to deliver an outstanding listening experience, making it a treasure for audiophiles and casual listeners alike.

One of the RCD-951's main features is its high-resolution DAC (Digital-to-Analog Converter). The unit employs a premium Wolfson DAC, which is renowned for its precision and ability to accurately convert digital signals into analog sound. This results in exceptionally clear and detailed playback, allowing listeners to experience their favorite music with unparalleled fidelity.

Additionally, the RCD-951 is equipped with an innovative anti-vibration chassis design. The robust construction minimizes resonance and external interference, ensuring that the sound quality remains uncolored and true to the original recording. This attention to detail in build quality is a hallmark of Rotel's philosophy, providing longevity and consistent performance over time.

Another key characteristic of the RCD-951 is its compatibility with a wide range of CD formats, including standard CDs, CD-Rs, and CD-RWs. This flexibility makes it a versatile player for those who enjoy compiling their music collections on recordable CDs. Moreover, the player features a direct digital output for easy integration into setups that utilize external DACs or digital signal processing equipment.

Ease of use is another advantage of the RCD-951, featuring an intuitive interface and a clear LCD display that allows users to navigate their music library effortlessly. The remote control further enhances convenience, enabling users to manage playback from a distance, which is perfect for larger audio setups.

The player's playback capabilities extend to programming and repeat functions, giving listeners control over how they enjoy their music. The smooth, reliable tray mechanism ensures that loading and unloading discs is a seamless process, further enhancing the user experience.

In conclusion, the Rotel RCD-951 is a refined and high-quality CD player that stands out due to its exceptional sound quality, versatile format compatibility, and solid construction. With features aimed at improving the listening experience, it remains a top choice for anyone seeking to elevate their audio setup. Whether used in a dedicated home audio system or as part of a larger multimedia arrangement, the RCD-951 proves that it is a worthy investment for any music lover.