Transition Networks RS-232-TO-100BASE-FX manual Connecting an alarm fixture, Fault, Indications

Page 28

Transition Networks

SDSFE31xx-100 Industrial Device Server

Connecting an alarm fixture, continued

Fault	Wire the relay contacts to any warning light or audible alarm in the factory or control
indications	room. Then when a fault occurs, the relay contacts close, sending a signal to activate
	an external alarm or turn ON a light, indicating a fault. An alarm will occur under
	the following conditions:
	• Any link failure cable disconnected, device break down .....)
	• PWR/RPS power failure:
	o Power wires are disconnected, power source malfunction
	o Input power is out of this range: 9 – 48V

16	24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Image 28

Contents Page Page Table of Contents Transition Networks Iii Intentionally Blank CE Mark Trademark Copyright restrictions FCC warningMay be required to take adequate preventative measures About this product and manual Box contents The box should include the following About this product and manualObserve this caution could result in EMI problems Equipment, or injury to personsDamage to the Device Server PerformanceSDSFE31xx-100 Industrial Device Server Transition Networks Intentionally Blank Section SDSFE31xx-100 Industrial Device Server This section These are the topicsTopic SeeGeneral description FeaturesOverview SDSFE31xx-100 Industrial part numbers StandardPhysical description PartsFunctions FunctionsPhysical description Device server parts and functionsIntentionally Blank Section Installation This sectionThese are the topics Topic SeeDevice Service mounting location DIN rail clip and DIN rail mounting Mounted DIN Rail ClipDIN rail clip and DIN rail mounting Step ActionGrounding the Device Server Device Server Grounding ScrewConnecting power to the Device Server Redundant Power ConnectionsConnecting power to the Device Server Turn the external power source OFFStrip the power wires as required Polarity. See FigureTerminal-block plug wiring Step Action Wired Terminal-Block Plug Inserted Into Device ServerConnecting an alarm fixture Alarm Relay ContactsFault Connecting an alarm fixtureIndications Connecting fiber cables Fiber Cable ConnectionsConnecting DB-9 cable InstallationSection for DB-9 cable pinouts DB-9 cableDIP Switches Dip Switch Settings and ExplanationsIntentionally Blank Section Operations Light emitting diodes LEDs LEDsDevice Server configuration Login Dialog BoxDevice Server configuration Web accessConfiguration software System RestartConfiguration software System information submenu Master information submenuConfiguration menu options Serial Port Transfer Configuration Submenu DisplaySerial port config submenu Submenu Item Description Serial Device Connection to a Host via Ethernet NetworkSerial Tunneling RS-232 Port Connection Status Submenu Display Submenu Item DescriptionSubmenu User configSee Figure Firmware Upgrade Submenu FW upgrade via Http Step Action Http Firmware File Name CapturedFW upgrade via Http Index Page System information DisplayFW upgrade via Tftp Step Action Configuration System Backup File Display Backup File Restore Display Snmp configuration menu Snmp communities submenu Snmp Communities DisplayDescribes the fields on the IP Trap Manager display IP Trap Parameters and DescriptionsIP trap manager submenu System restore System RestoreReset Will be erasedIntentionally Blank Section Section Serial IP Redirector SoftwareThis are the topics Serial IP redirect software description What is Needed? Step ActionInstalling serial IP redirector software Installation Wizard Dialog BoxInstalling serial IP redirector software Software Destination Folder Dialog BoxSelect Features Dialog Box Ready to Install Application Dialog Box Step Action Software upgrades Upgrading serial IP redirector softwareCreating virtual COM ports Serial IP Control Panel Dialog BoxCreating virtual COM ports Select Ports Dialog BoxVirtual Port Configuration COM Port 7 Configuration Wizard Setting button will be active. See Figure If the wizardFails If the wizard isIf the wizard is successful Step Action Serial/IP Port MonitorTroubleshooting problem and corrective action table Section TroubleshootingIntroduction Troubleshooting problem and corrective action table Problem Potential Cause Potential SolutionSection Cable Specifications This section provides copper and fiber cable specificationsCopper DB-9 RS-232serial cable specifications What is RS-232Specifications PinoutsParameterSpecification Fiber cable and optic specificationsFiber Cable Specifications Intentionally Blank Section Contact Us, Warranty Conformity Information Contact us Conformity declaration Declaration of ConformityWarranty Warranty Compliance information CompliancesRegulations CanadianCompliance information Accordance with European Union Directive 2002/96/ECPortion of this document To the Public Telephone NETWORK. Failure to observe thisIntentionally Blank SDSFES31xx-100 specifications, notices, and warnings Appendix a Technical SpecificationParameter Description SDSFES31xx-100 specifications, notices, and warnings Subchapter J applicable at the date of manufactureCould result in damage to equipment This warning could result in an eye injury or blindnessCOM Port Configuration IndexPacket Mode