Transition Networks RS-232-TO-100BASE-FX Connecting DB-9 cable, Section for DB-9 cable pinouts

Page 30

Transition Networks

SDSFE31xx-100 Industrial Device Server

Connecting DB-9 cable

DB-9 cable Depending on the equipment type, data terminal equipment (DTE) or data configuration communication equipment (DCE), use a null modem (crossover) or straight-through

cable. See Figure 13.

	Figure 12: Straight Through and Crossover Cables
	Note: The Device Server is configured as a DTE Device. See Cable Specification
		Section for DB-9 cable pinouts.

DB-9 cable	To connect the DB-9 (RS-232)cable to the Device Server and other equipment, do
installation	the following:

	Step		Action
	1.		Insert one end of the RS-232 cable into the Device Server.
	2.		Tighten the screws to secure the cable.
	3.		Repeat Steps 1 and 2 for the other equipment. See Figure 12.
	4.		Test the connection by sending a link pulse to the Device Server and the
			ACT LED will flash, indicating a good connection.

Figure 13: DB-9 Cable Installation

18	24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Image 30

Contents Page Page Table of Contents Transition Networks Iii Intentionally Blank Trademark Copyright restrictions FCC warning CE MarkMay be required to take adequate preventative measures About this product and manual Box contents The box should include the following About this product and manualDamage to the Device Server Observe this caution could result in EMI problemsEquipment, or injury to persons PerformanceSDSFE31xx-100 Industrial Device Server Transition Networks Intentionally Blank Topic Section SDSFE31xx-100 Industrial Device ServerThis section These are the topics SeeFeatures General descriptionOverview SDSFE31xx-100 Industrial part numbers StandardFunctions Physical descriptionParts FunctionsPhysical description Device server parts and functionsIntentionally Blank These are the topics Section InstallationThis section Topic SeeDevice Service mounting location DIN rail clip and DIN rail mounting Mounted DIN Rail ClipDIN rail clip and DIN rail mounting Step ActionGrounding the Device Server Device Server Grounding ScrewConnecting power to the Device Server Redundant Power ConnectionsStrip the power wires as required Connecting power to the Device ServerTurn the external power source OFF Polarity. See FigureTerminal-block plug wiring Step Action Wired Terminal-Block Plug Inserted Into Device ServerConnecting an alarm fixture Alarm Relay ContactsConnecting an alarm fixture FaultIndications Connecting fiber cables Fiber Cable ConnectionsSection for DB-9 cable pinouts Connecting DB-9 cableInstallation DB-9 cableDIP Switches Dip Switch Settings and ExplanationsIntentionally Blank Section Operations Light emitting diodes LEDs LEDsDevice Server configuration Login Dialog BoxDevice Server configuration Web accessConfiguration software System RestartConfiguration software System information submenu Master information submenuConfiguration menu options Serial Port Transfer Configuration Submenu DisplaySerial port config submenu Submenu Item Description Serial Device Connection to a Host via Ethernet NetworkSerial Tunneling RS-232 Port Connection Status Submenu Display Submenu Item DescriptionUser config SubmenuSee Figure Firmware Upgrade Submenu FW upgrade via Http Step Action Http Firmware File Name CapturedFW upgrade via Http Index Page System information DisplayFW upgrade via Tftp Step Action Configuration System Backup File Display Backup File Restore Display Snmp configuration menu Snmp communities submenu Snmp Communities DisplayDescribes the fields on the IP Trap Manager display IP Trap Parameters and DescriptionsIP trap manager submenu Reset System restoreSystem Restore Will be erasedIntentionally Blank Section Serial IP Redirector Software SectionThis are the topics Serial IP redirect software description What is Needed? Step ActionInstalling serial IP redirector software Installation Wizard Dialog BoxInstalling serial IP redirector software Software Destination Folder Dialog BoxSelect Features Dialog Box Ready to Install Application Dialog Box Step Action Software upgrades Upgrading serial IP redirector softwareCreating virtual COM ports Serial IP Control Panel Dialog BoxCreating virtual COM ports Select Ports Dialog BoxVirtual Port Configuration COM Port 7 Configuration Wizard Fails Setting button will be active. See FigureIf the wizard If the wizard isIf the wizard is successful Step Action Serial/IP Port MonitorSection Troubleshooting Troubleshooting problem and corrective action tableIntroduction Troubleshooting problem and corrective action table Problem Potential Cause Potential SolutionSection Cable Specifications This section provides copper and fiber cable specificationsSpecifications Copper DB-9 RS-232serial cable specificationsWhat is RS-232 PinoutsFiber cable and optic specifications ParameterSpecificationFiber Cable Specifications Intentionally Blank Section Contact Us, Warranty Conformity Information Contact us Conformity declaration Declaration of ConformityWarranty Warranty Regulations Compliance informationCompliances CanadianPortion of this document Compliance informationAccordance with European Union Directive 2002/96/EC To the Public Telephone NETWORK. Failure to observe thisIntentionally Blank Appendix a Technical Specification SDSFES31xx-100 specifications, notices, and warningsParameter Description Could result in damage to equipment SDSFES31xx-100 specifications, notices, and warningsSubchapter J applicable at the date of manufacture This warning could result in an eye injury or blindnessCOM Port Configuration IndexPacket Mode