Keating Of Chicago Gas Custom Pasta System manual Iv Maintenance, Warranty Repairs, Digital Timers

Page 12
B.How to program the “Keating” Electronic Timer

B.How to program the “Keating” Electronic Timer

￿The Keating Electronic Timer is programmable to four different timer ranges with two different alarm modes for each time range.

￿The timers are shipped from the factory preset to program 5: Minutes : seconds (00:01 to 59:59) with continuous alarm

￿To program another time range or alarm mode perform the following steps:

1.Turn off the power

2.Press the “down arrow “ button while turning the power on.

3.Release the button after the display turns on.

4.A number from 0 to 7 will appear.

This number corresponds to:

0 = Seconds (000.1 to 999.9) 5 second alarm

1 = Minutes : Seconds (00:01 to 59:59) 5 second alarm

2 = Seconds (0001 to 9999) 5 second alarm

3 = Hours : Minutes (00:01 to 23:59) 5 second alarm

4 = Seconds (000.1 to 999.9) continuous alarm

5 = Minutes : Seconds (00:01 to 59:59) continuous alarm

6 = Seconds (0001 to 9999) continuous alarm

7 = Hours : Minutes (00:01 to 23:59) continuous alarm

5.Use the “down arrow “ button to select the desired time range.

6.Turn off the power.

7.Wait 2 seconds.

8.Turn on the power. (The timer will remain in the new time range until programmed.) The electronic timers, used on 18" and above Basket-Lift models, provide a clearly visible and accurate display and are very easy to use. One knob sets the time and one button controls all operations. The display can show cooking or clock time.

ELECTRONIC TIMER

OPERATING INSTRUCTIONS

PART # 056921

DIGITAL TIMERS

The electronic timers, standard on pasta cookers, provide a clearly visible and accurate display and are very easy to use.

PROGRAMMING

To program the timers, the unit must be in the idle mode. Press and hold the set button for approximately two seconds. The display will show “SEt”. Press the button for the channel to be programmed. The display will show the current setting for that channel. Use the up or down button to increment or decrement the setting. When the setting is correct, press and hold the set button again for approximately two seconds. The display will show "StO" for approximately two seconds and the timer will return to normal operation. Repeat the process as necessary for the other timers.

OPERATING LOGIC

When the timer is powered up, the display will show the time setting for the channel that was operated last and the relay output contacts will be open. To start a cycle, press the desired channel button (1-3). The display will begin to countdown from the preset time setting and the relay output contacts will close. During the countdown the colon will flash at a one-second rate. When the countdown has reached "00:00" the relay output contacts will open, the display will flash, and the audible alarm will sound. To cancel the audible alarm, press any button.

PAUSE FEATURE

To pause a cycle in progress, press any button. The relay output contacts will open, the display will flash, and the countdown will pause. To resume the countdown, press any button. The display will resume the normal countdown and the relay output contacts will close.

CANCELING A CYCLE

To cancel a cycle in progress press and hold any button for approximately two seconds. The relay output contacts will open and the display will show the time setting for the channel last used.

IV MAINTENANCE

WARRANTY REPAIRS

Keating’s warranty begins with the date of installation. In the event that your Pasta System, under warranty, needs repairs other than routine maintenance or cleaning, you are requested to contact Keating of Chicago, Inc.

9

Page 11 Page 13
Image 12
Page 11 Page 13
Contents KEEP THIS MANUAL FOR TRAINING NEW PERSONNEL 1-800-KEATINGGas Pasta 0107 9/07 POST THIS LABEL IN A PROMINENT LOCATION ON YOUR UNIT TABLE OF CONTENTS SECTION II INSTALLATIONSECTION IV MAINTENANCE SECTION V SERVICE DIAGNOSISI INTRODUCTION STANDARD FEATURESSTANDARD ACCESSORIES SAFETY PRECAUTIONSCLEARANCES II INSTALLATION INSTALLATIONPOSITIONING CLEARANCES DAMAGE DURING SHIPMENTSPECIFICATIONS RESTRAINING DEVICESGAS CONNECTION HAVE YOUR PLUMBER OR GAS COMPANY CHECK FOR LEAKSGAS LEAK TESTING ELECTRICAL CONNECTIONCHECK GAS SUPPLY PRESSURE SPECIAL NOTICESIII OPERATING CALIBRATIONWATER AND DRAIN CONNECTIONS FILLINGINDICATING LIGHTS COOKINGSHUTDOWN DRAININGCLEANING ELECTRONIC TIMERSDisconnect electric power source before cleaning A. Timer OperationIV MAINTENANCE ELECTRONIC TIMER OPERATING INSTRUCTIONS PART #WARRANTY REPAIRS B. How to program the “Keating” Electronic TimerPREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE CHARTB. The Water Auto-Fill and Low Water Safety Shut- Off Systems LIMITED CALIBRATIONUsing a worn brush could damage the sensors PROBLEM SOLUTIONPROBABLE CAUSE PROBLEM SOLUTIONS Follow Sequentially REPLACEMENT OF A AND B BOARDS V SERVICE DIAGNOSIS CUSTOM PASTA SYSTEM CONTROL PANEL WITH DIGITAL TIMERSMANUAL FILL CUSTOM PASTA SYSTEM CONTROL PANEL WITH DIGITAL TIMERS GAS PASTA SYSTEM ASSEMBLY MODELSPART# GAS PASTA SYSTEM ASSEMBLY PASTA SYSTEM WIRING DIAGRAM GAS PASTA SYSTEM WITH BASKET-LIFT WIRING DIAGRAM WARRANTY The Customer must provide proof of purchase from KeatingKEATING SERVICE INFORMATION If you have a service related question call 1-800-KEATINGHave your serial and model number available when ordering parts “Serving Those Who Serve The Very Best”
Top Page Image Contents