Keating Of Chicago Gas Custom Pasta System manual Cleaning, Electronic Timers, A. Timer Operation

Page 11
CLEANING

1. Turn off Pasta System and open the door.

Figure 3-3

Drain, drain valve and overflow tubing

Over flow tubing

2.Slowly turn handle. The drain valve will be completely open after 1/4 turn.

CLEANING

When cleaning and boiling out your Pasta System, use white vinegar and Keating Klenzer to keep your Pasta System in top condition. Once your Pasta System vessel is clean, use Keating Klenzer, the finest dry stainless steel polish available, to restore your Keating Gas Pasta System’ exterior to its original luster.

Disconnect electric power source before cleaning.CAUTION

Disconnect electric power source before cleaning.

ELECTRONIC TIMERSCAUTION

To avoid damaging the Pasta System, do not power wash, spray or hose it down while cleaning.

1.Operator should be outfitted with proper attire including:

–Water and heat resistant gloves –Water and heat resistant apron –Safety goggles

–Water and heat resistant footwear

2.Turn the Pasta System off.

3.Drain water from Pasta System.

4.Fill Pasta System vessel with water. See page 7 – Filling.

A. Timer OperationWARNING

UNDER NO CIRCUMSTANCES SHOULD THE PASTA SYSTEM BE LEFT UNATTENDED DURING BOIL-OUT. TRAINED PERSONNEL MUST BE PRESENT DURING THE PROCEDURE TO PREVENT BOIL OVER OR TO TURN OFF THE POWER IF WATER DROPS BELOW HEAT TRANSFER TUBES.

5.Turn Pasta System on and bring water and a gentle boil.

6.Once boil has been reached, turn Pasta System off.

7.Dissolve 3 cups of vinegar for every five gallons of water and let soak for one hour. If there is a large build-up of scale, allow Pasta System to soak overnight.

8.While soaking, a natural fiber brush may be used to scrub the tubes and inside walls of Pasta System vessel.

9.Drain the water and vinegar.

10.Spread Keating Klenzer liberally on tubes and sides of Pasta System vessel.

11.At this point, a non-abrasive scouring pad may be used to remove any leftover scale.

12.Thoroughly rinse Pasta System vessel with potable water to remove all Klenzer.

13.Prior to refilling with water, wipe the inside of the Pasta System vessel making sure all water and Klenzer has been removed.

14.Close drain valve.

15.Refill the Pasta System with fresh water. See page 6 – Filling.

ELECTRONIC TIMERS

The electronic timers, provide a clearly visible and accurate display and are very easy to use.

A. Timer Operation

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Gas Pasta 0107 9/07 KEEP THIS MANUAL FOR TRAINING NEW PERSONNEL1-800-KEATING POST THIS LABEL IN A PROMINENT LOCATION ON YOUR UNIT SECTION V SERVICE DIAGNOSIS TABLE OF CONTENTSSECTION II INSTALLATION SECTION IV MAINTENANCESAFETY PRECAUTIONS I INTRODUCTIONSTANDARD FEATURES STANDARD ACCESSORIESCLEARANCES DAMAGE DURING SHIPMENT II INSTALLATIONINSTALLATION POSITIONING CLEARANCESHAVE YOUR PLUMBER OR GAS COMPANY CHECK FOR LEAKS SPECIFICATIONSRESTRAINING DEVICES GAS CONNECTIONSPECIAL NOTICES GAS LEAK TESTINGELECTRICAL CONNECTION CHECK GAS SUPPLY PRESSUREFILLING III OPERATINGCALIBRATION WATER AND DRAIN CONNECTIONSDRAINING INDICATING LIGHTSCOOKING SHUTDOWNA. Timer Operation CLEANINGELECTRONIC TIMERS Disconnect electric power source before cleaningB. How to program the “Keating” Electronic Timer IV MAINTENANCEELECTRONIC TIMER OPERATING INSTRUCTIONS PART # WARRANTY REPAIRSLIMITED CALIBRATION PREVENTIVE MAINTENANCEPREVENTIVE MAINTENANCE CHART B. The Water Auto-Fill and Low Water Safety Shut- Off SystemsUsing a worn brush could damage the sensors PROBABLE CAUSE PROBLEMSOLUTION PROBABLE CAUSE SOLUTIONS Follow Sequentially REPLACEMENT OF A AND B BOARDS CUSTOM PASTA SYSTEM CONTROL PANEL WITH DIGITAL TIMERS V SERVICE DIAGNOSISMANUAL FILL CUSTOM PASTA SYSTEM CONTROL PANEL WITH DIGITAL TIMERS PART# GAS PASTA SYSTEM ASSEMBLYMODELS PART# PASTA SYSTEM WIRING DIAGRAM GAS PASTA SYSTEM WITH BASKET-LIFT WIRING DIAGRAM KEATING WARRANTYThe Customer must provide proof of purchase from Keating “Serving Those Who Serve The Very Best” SERVICE INFORMATIONIf you have a service related question call 1-800-KEATING Have your serial and model number available when ordering parts
Top Page Image Contents