Troy-Bilt TB3516 STARTING/STOPPING Instructions, Stopping Instructions, Chain properly installed

Page 10

STARTING/STOPPING INSTRUCTIONS

WARNING: Never operate the saw without the bar and

chain properly installed.

STARTING INSTRUCTIONS

1.Fill the oil tank with correct chain and bar oil (Fig. 3). Use a funnel, wipe up any spills and make sure no dirt gets into the tank.

NOTE: The saw chain requires lubrication when in use to minimize friction with the guide bar. The oil tank holds 4.5 ozs of oil, enough to lubricate the chain for 12-15 minutes of sawing. We recommend using original equipment manufacturer Bar and Sprocket Oil, which contains additives to reduce friction wear and reduce resin residue formations.

CAUTION: The oil tank level should be frequently

checked during operation to avoid starving the bar and chain of lubrication.

NOTE: Your chain saw is equipped with an Automatic Oiler system and is the ONLY source of lubrication for the bar and chain.

2.Be certain the Chain Brake® is disengaged before starting unit (Fig. 4). Disengage it by pulling backward toward the motor.

3.Hook the extension cord to the extension cord retainer

(A) (Fig. 5) that is built into the rear handle. This will prevent the cord from pulling out of the handle. Double the extension cord, about a foot from the end, and insert it through the hole at the end of the handle. Hook the loop formed by doubling the cord over the tab. Gently tug on the cord to ensure that it is firmly retained in the saws handle. Plug the receptacle end of the extension cord into the tool’s power supply cord.

WARNING: Ensure the extension cord is of the proper

size and type for your saw.

4.Grip the saw with both hands, left hand holding the front /handle (DO NOT HOLD CHAIN BRAKE®) and the right hand holding the rear handle. Thumbs and fingers should encircle both handles (Fig. 6).

WARNING: Make sure the extension cord does

not come in contact with the guide bar and saw chain.

5.With your right thumb, depress the LOCK/OFF button

(C) on the top of the rear handle, and at the same time squeeze the trigger. To stop the saw, release the trigger (Fig. 7).

NOTE: It is not necessary to maintain pressure on the LOCK/OFF button once the trigger is squeezed and the motor is running. The LOCK/OFF button is a safety device to avoid accidental starting.

STOPPING INSTRUCTIONS

The saw motor will automatically stop when the trigger is released. To restart the motor, you will have to depress the LOCK/OFF button and squeeze the trigger.

Oil Cap

Oil Tank

Inspection Spot

Fig. 3

Fig. 4

A

Fig. 5

Fig. 6

C

Fig. 7

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Save These Instructions do not Throw AwayTable of Contents Product REFERENCES, Illustrations and SpecificationsService Information IntroductionBefore Operating Important Safety InstructionsRules for Safe Operation While OperatingKickback Safety Precautions Other Safety Precautions Electrical Safety WarningsElectrical Safety Warnings CONT’D Double Insulated Safety and International SymbolsSymbol Meaning Do not USE in the RainSafety Features Chain SAW ComponentsRotational Kickback Kickback SpecificsPinch Kickback Stopping Instructions Chain properly installedSTARTING/STOPPING Instructions Size and type for your sawFelling Operating InstructionsArea for bystanders, animals or obstacles Bucking Bucking Using a SawhorseLimbing Chain and bar are being properly lubricatedInstall the SAW Chain Maintenance and Repair InstructionsInstall the Guide BAR Source before checking or adjusting the chain saw tensionSAW Chain Tension Adjustment Chain Brake / Hand Guard Chain and BAR LubricationFor starting and stopping the saw during normal operation Extension Cords MaintenanceChain Brake Test Double InsulationDisconnected before performing any maintenance on your saw Guide BAR MaintenanceMaintenance Procedures Sprocket Tip LubricationChain Maintenance Chain Replacement InformationU S E TroubleshootingSpecifications / Features T I O NTroy-Bilt LLC Manuel de Lutilisateur Manuel ImportantInformations D’ENTRETIEN Tous NOS RemerciementsTable DES Matières Mise EN Garde le non Alerte DE SécuritéAvertissement le non Importantes Consignes DE SécuritéAvertissement Les rebonds Avertissements DE Sécurité Électrique Avertissement Pourréduire leAutres Précautions DE Sécurité Ampère Voltage c.a Longueur du Câble d’Alimentation Conserver CES InstructionsCalibre de Fil Minimum 5m / 25 pl 15m / 50 pl 30m / 100 plSymboles DE Sécurité ET Internationaux AvertissementComposants DE LA Tronçonneuse Dispositifs DE SecuriteAvertissement Lesrebonds Rebonds Conseils SupplementairesAvertissement S’assurer Avertissement N’opérezAvertissement S’assure Instructions DE Démarrage ET ArrêtAvertissement Avant la Mode DemploiAvertissement Eviter la AbattageEbranchage Avertissement Ne jamaisMise EN Garde S’assurer TronconnageEntretien ET Réparations Installation DE LA ChaineMise EN Garde Démontez Nstallation DU GUIDE-CHAINEReglage DE LA Tension DE LA Chaine Reglage DE LA Tension DE LA ChaineMise EN Garde Chain Mise EN Garde nejamaisAvertissement Une Chain Brake / Arceau ProtecteurDouble Isolation Avertissement Si laAvertissement Nepas Test DE Chain BrakeLubrification de la Roulette Entretien DU GUIDE-CHAINESi la roulette Avertissement Amoins Renseignements SUR LE Remplacement DE LA ChaîneEntretien DE LA Chaine Caractéristiques DépannageL U T I O N Garantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Este Manual ES ImportanteIndice DE Contenidos IntroduccionMuchas Gracias REFERENCIAS, Ilustraciones Y Especificaciones DEL ProductoSI Tiene PREGUNTAS, Llame AL Importante Informacion DE SeguridadNormas Para UNA Operacion Segura LEA Todas LAS Instrucciones Antes DE LA OperacionAdvertencia El con Protejase Contra EL ContragolpeAdvertencias DE Seguridad Electrica Advertencia Para reducirOtras Precauciones DE Seguridad Conserve Estas Instrucciones Advertencia Evite Advertencia LosSimbolos DE Seguridad E Internacionales Componentes DE LA Sierra DE Cadena Aspectos DE SeguridadMAS Acerca DEL Contragolpe El ContragolpeAdvertencia Asegúrese Advertencia NuncaPrecaucion El nivel de Instrucciones DE Arranque Y ApagadoAdvertencia Antes de Advertencia Un senderoAdvertencia No corte un Advertencia Al tiempoLeñado Precaucion Mientras laDesramado Leñado Usando UN Caballete Para AserrarPara Instalar LA Barra Guia Precaucion DesconecteInstrucciones DE Mantenimiento Y Reparacion Para Instalar LA Sierra DE LA CadenaAjustes DE Tension DE LA Cadena DE LA Sierra Instrucciones DE EnsamblePrecaucion Si la cadena De la sierra Precaucion Durante la Precaucion Nunca dejeAdvertencia Unacadena Chain Brake / GuardamanosAdvertencia No opere su Advertencia Si el motorPrecaucion Un cable Advertencia Su aparatoMantenimiento DE LA Barra Guia Erramientas Para la LubricaciónMantenimiento DE LA Cadena Advertencia a menos deInformación Sobre EL Reemplazo DE LA Cadena U S a Resolucion DE ProblemasEspecificaciones C I O NNotas E21 E22 Parts List Model TB3516/TB4516CCGarantía Limitada DEL Fabricante Para
Top Page Image Contents