Shindaiwa DH212, 82053 manual Install blade stiffener, Blade stiffener removal

Page 10

ENGLISH

Install blade stiffener

1.Move stop switch to stop position.

2.Disconnect spark plug wire.

WARNING

Hedge trimmer blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when adjust- ing blade bolts or blade locknuts in order to keep hands at a safe distance from sharp blades.

3.Lay unit on muffler side and hold securely in place.

4.Remove first four blade locknuts (A) and washers in front of front handle/guard. Do not remove blade bolts.

5.Tighten blade bolts (B) until snug. Install blade stiffener, then washers.

6.Loosen blade bolts ½ turn. Secure blade stiffener with new locknuts

(A). Hold blade bolts from turning using a 10mm wrench.

Note

Use new locknuts every time blade stiffener is installed.

IMPORTANT

If blade stiffener is damaged or show signs of wear, replace it.

Note

Washers (C) should be movable by hand after blade bolts are adjusted properly.

A

B

C

Blade stiffener removal

1.Move stop switch to stop position.

2.Disconnect spark plug wire.

WARNING

Hedge trimmer blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when adjust- ing blade bolts or blade locknuts in order to keep hands at a safe distance from sharp blades.

3.Remove blade stiffener locknuts (A) and washers. Do not remove blade bolts.

4.Remove blade stiffener.

5.Tighten blade bolts (B) until snug, then loosen ½ turn.

6.Secure blades with new locknuts (A). Hold blade bolts from turning using a 10mm wrench.

A

B

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DH212 Hedge Trimmer Introduction Table of ContentsOperator’s manual International symbols Safety Manual safety symbols and important informationPersonal condition and safety equipment Hand Protection Physical ConditionEye Protection Hearing ProtectionClear the Work Area Repetitive Stress InjuriesRead the Manuals Keep a Firm GripEmission Control EPA Phase 2/ C.A.R.B. TierEquipment check Product Emission DurabilityRight Front Handle Guard DescriptionEnglish Contents AssemblyInstall blade stiffener Blade stiffener removalOperation Fuel RequirementsFuel Fuel to Oil Mix-501 Ratio Handling FuelAfter use MetricStarting cold engine Purge BulbStarting warm engine Stopping engineHedge trimming MaintenanceSkill levels Maintenance intervals Do-It-Yourself Maintenance ProceduresFuel filter Air filterLevel Cooling system Spark plugRemaining sand will damage engine English Cylinder Exhaust Port Spark Arrestor ScreenExhaust system Engine Break-In Carburetor adjustmentHigh Altitude Operation Blades Gear Box AssemblyLubrication Sharpening blades Blade adjustment Troubleshooting Long Term Storage over 30 days StorageSpecifications Model DH212What does this Warranty COVER? Manufacturers Warranty CoverageOwners Warranty Responsibilities HOW will a Covered Part be CORRECTED?English English English Shindaiwa Inc Shindaiwa Corporation 11975 S.W. Herman Rd Cortadora DE Setos DH212 Tabla de materias IntroducciónEl manual del operador ImportanteSímbolos internacionales Forma de los SímbolosProtección de las manos Condición físicaProtección de los ojos Protección de los oídosDespeje el área de trabajo Lesiones debidas a esfuerzos repetitivosLea los manuales Agarre bien la unidadControl de emisiones Fase 2 de EPA / Nivel III de C.A.R.BEquipos Durabilidad DE LAS Emisiones DEL ProductoDescripción Cerca del silenciadorSP8 Montajeo ContenidoNota Desmontaje del refuerzo de hoja Instale el refuerzo de la hojaNota Operación Requisitos del combustibleCombustible Manipulación del combustible Instrucciones de mezclaArranque del motor en frío CebadorArranque con el motor caliente Parada del motorNiveles de habilidad Recorte de setosMantenimiento ¡IMPORTANTEIntervalos de mantenimiento Procedimientos De Mantenimiento De Do-It-YourselfFiltro de combustible Filtro de aireNivel Bujía Sistema de enfriamientoSP19 Orificio de escape del cilindro Rejilla del apagachispasSistema de escape Ajuste del carburador Rodaje del motorAjuste de altitud elevada ImportanteConjunto de la caja de engranajes HojasLubricación Afilado de las hojas Ajuste de la hoja Localización y reparación de fallas Almacenamiento a largo plazo más de 30 días AlmacenamientoEspecificaciones Modelo HC-150Relacionados CON Emisiones EPA Phase 2 / California Relacionados CON LAS Emisiones EPA PhaseCalifornia Tier III Emissions Defect Warranty EN Piezas Cubiertas POR LA Garantía Contra DefectosNotas SP30 SP31 Shindaiwa Inc Shindaiwa Corporation TAILLE-HAIE DH212 Le manuel d’utilisation Table des matièresSymboles internationaux Sécurité Symboles de sécurité et informations importantesCondition physique et équipement de sécurité Protection des mains Condition physiqueProtection des yeux Protection auditiveDégagez la zone de travail Microtraumatismes répétésLisez les manuels Garder une bonne priseContrôle des émissions EPA Phase 2 / C.A.R.B. TierÉquipement Durabilité DU Contrôle DES ÉmissionsGarde de poignée avant droite Autocollant de danger de Brûlures près du silencieuxFR8 Assemblage ContenuRemarque Installation du raidisseur de lame Retrait du raidisseur de lameUtilisation Spécifications pour le carburantCarburant Après utilisation Manipulation du carburantInstructions de mélange RemisageDémarrage d’un moteur froid RemarqueDémarrage d’un moteur chaud Arrêt du moteurTaille EntretienNiveaux de difficulté Intervalles d’entretienFiltre à carburant Filtre à airNiveau Bougie Système de refroidissementRetirer l’écran de chaleur C du couvercle du silencieux Lumière d’échappement du cylindre Pare-étincellesSystéme déchappement Réglage pour haute altitude Rodage du moteurReglage du carburateur Assemblage du carter d’engrenages LamesLubrification Affûtage des lames Ajustement de lame Dépannage Remisage à long terme plus de 30 jours RemisageCaractéristiques Modèle DH212CE QUE Couvre Cette Garantie Couverture DE LA Garantie DES FabricantsResponsabilités DU Propriétaire À L’ÉGARD DE LA Garantie EN CAS DE Pièce DéfectueuseRemarques FR30 FR31

82053, DH212 specifications

The Shindaiwa 82053, DH212 is a powerful and versatile tool designed for professionals in the landscaping and horticultural industries. Known for its robust performance and reliability, this product stands out among its peers due to several innovative features and technologies tailored to meet the needs of demanding users.

One of the main highlights of the Shindaiwa 82053 is its powerful engine. This tool is equipped with a high-performance engine that delivers exceptional cutting power while maintaining fuel efficiency. The engine's design minimizes vibration and ensures smooth operation, allowing users to work effectively without excessive fatigue.

The DH212, a key component of the Shindaiwa 82053, is recognized for its ergonomic design. This feature enhances user comfort during extended periods of operation. The handles are thoughtfully designed to provide superior grip and control, reducing the strain on the operator's hands and arms. This is particularly important for professionals who often work long hours.

Another significant characteristic of the Shindaiwa 82053 is its advanced cutting technology. The dual-edge blade system provides a cleaner and faster cut, allowing for efficient trimming of hedges and bushes. The blades are crafted from high-quality materials that ensure durability and longevity, even under heavy use.

The tool's rapid-start feature is designed to reduce startup time, enabling users to get to work quickly without unnecessary delays. Additionally, the advanced air filtration system helps to keep the engine clean, extending its lifespan and improving reliability.

The Shindaiwa 82053, DH212 is also known for its easy maintenance. The design incorporates accessible components, allowing users to perform routine checks and repairs with minimal hassle. This user-friendly approach reduces downtime and enhances productivity.

In terms of safety, the Shindaiwa 82053 features multiple safeguards that protect the user during operation. The protective guards and blade covers ensure that operators can work confidently without the fear of accidental injuries.

Overall, the Shindaiwa 82053, DH212 embodies a perfect blend of power, comfort, and advanced technology, making it an ideal choice for professional landscapers and gardeners. Its exceptional performance and reliability are sure to make it a trusted tool in any landscaping arsenal. Whether trimming hedges or maintaining gardens, the Shindaiwa 82053 is a dependable ally that ensures work is completed efficiently and effectively.
Top Page Image Contents