Shindaiwa DH212, 82053 manual Handling Fuel, After use, Fuel to Oil Mix-501 Ratio, Metric

Page 12

ENGLISH

Handling Fuel

warning

Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

•Use an approved fuel container.

•DO NOT smoke near fuel.

•DO NOT allow flames or sparks near fuel.

•Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

•NEVER refuel a unit when the engine is HOT or RUNNING!

•DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

•DO NOT overfill fuel tank. Wipe up spills immediately.

•Securely tighten fuel tank cap and close fuel container after refueling.

•Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

•Move at least 3m (10 ft.) from refueling location before starting the engine.

Mixing Instructions

1.Fill an approved fuel container with half of the required amount of gasoline.

2.Add the proper amount of 2-stroke oil to gasoline.

3.Close container and shake to mix oil with gasoline.

4.Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.

After use

•DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local gov- ernment for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames.

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.

Fuel to Oil Mix-50:1 Ratio

U.S.METRIC

GAS

OIL

GAS

OIL

Gallons

Fl.oz.

Liter

cc.

1

2.6

4

80

2

5.2

8

160

5

13

20

400

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DH212 Hedge Trimmer Table of Contents IntroductionOperator’s manual Safety Manual safety symbols and important information International symbolsPersonal condition and safety equipment Physical Condition Eye ProtectionHand Protection Hearing ProtectionRepetitive Stress Injuries Read the ManualsClear the Work Area Keep a Firm GripEPA Phase 2/ C.A.R.B. Tier Equipment checkEmission Control Product Emission DurabilityRight Front Handle Guard DescriptionEnglish Contents AssemblyInstall blade stiffener Blade stiffener removalFuel Requirements OperationFuel Handling Fuel After useFuel to Oil Mix-501 Ratio MetricStarting cold engine Purge BulbStarting warm engine Stopping engineMaintenance Hedge trimmingSkill levels Maintenance intervals Do-It-Yourself Maintenance ProceduresAir filter Fuel filterLevel Spark plug Cooling systemRemaining sand will damage engine English Spark Arrestor Screen Cylinder Exhaust PortExhaust system Carburetor adjustment Engine Break-InHigh Altitude Operation Gear Box Assembly BladesLubrication Sharpening blades Blade adjustment Troubleshooting Long Term Storage over 30 days StorageSpecifications Model DH212Manufacturers Warranty Coverage Owners Warranty ResponsibilitiesWhat does this Warranty COVER? HOW will a Covered Part be CORRECTED?English English English Shindaiwa Inc Shindaiwa Corporation 11975 S.W. Herman Rd Cortadora DE Setos DH212 Introducción El manual del operadorTabla de materias ImportanteSímbolos internacionales Forma de los SímbolosCondición física Protección de los ojosProtección de las manos Protección de los oídosLesiones debidas a esfuerzos repetitivos Lea los manualesDespeje el área de trabajo Agarre bien la unidadFase 2 de EPA / Nivel III de C.A.R.B EquiposControl de emisiones Durabilidad DE LAS Emisiones DEL ProductoDescripción Cerca del silenciadorSP8 Contenido MontajeoNota Instale el refuerzo de la hoja Desmontaje del refuerzo de hojaNota Requisitos del combustible OperaciónCombustible Manipulación del combustible Instrucciones de mezclaArranque del motor en frío CebadorArranque con el motor caliente Parada del motorRecorte de setos MantenimientoNiveles de habilidad ¡IMPORTANTEIntervalos de mantenimiento Procedimientos De Mantenimiento De Do-It-YourselfFiltro de aire Filtro de combustibleNivel Bujía Sistema de enfriamientoSP19 Rejilla del apagachispas Orificio de escape del cilindroSistema de escape Rodaje del motor Ajuste de altitud elevadaAjuste del carburador ImportanteHojas Conjunto de la caja de engranajesLubricación Afilado de las hojas Ajuste de la hoja Localización y reparación de fallas Almacenamiento a largo plazo más de 30 días AlmacenamientoEspecificaciones Modelo HC-150Relacionados CON LAS Emisiones EPA Phase California Tier III Emissions Defect Warranty ENRelacionados CON Emisiones EPA Phase 2 / California Piezas Cubiertas POR LA Garantía Contra DefectosNotas SP30 SP31 Shindaiwa Inc Shindaiwa Corporation TAILLE-HAIE DH212 Le manuel d’utilisation Table des matièresSécurité Symboles de sécurité et informations importantes Symboles internationauxCondition physique et équipement de sécurité Condition physique Protection des yeuxProtection des mains Protection auditiveMicrotraumatismes répétés Lisez les manuelsDégagez la zone de travail Garder une bonne priseEPA Phase 2 / C.A.R.B. Tier ÉquipementContrôle des émissions Durabilité DU Contrôle DES ÉmissionsGarde de poignée avant droite Autocollant de danger de Brûlures près du silencieuxFR8 Contenu AssemblageRemarque Installation du raidisseur de lame Retrait du raidisseur de lameSpécifications pour le carburant UtilisationCarburant Manipulation du carburant Instructions de mélangeAprès utilisation RemisageDémarrage d’un moteur froid RemarqueDémarrage d’un moteur chaud Arrêt du moteurTaille EntretienNiveaux de difficulté Intervalles d’entretienFiltre à air Filtre à carburantNiveau Bougie Système de refroidissementRetirer l’écran de chaleur C du couvercle du silencieux Pare-étincelles Lumière d’échappement du cylindreSystéme déchappement Rodage du moteur Réglage pour haute altitudeReglage du carburateur Lames Assemblage du carter d’engrenagesLubrification Affûtage des lames Ajustement de lame Dépannage Remisage à long terme plus de 30 jours RemisageCaractéristiques Modèle DH212Couverture DE LA Garantie DES Fabricants Responsabilités DU Propriétaire À L’ÉGARD DE LA GarantieCE QUE Couvre Cette Garantie EN CAS DE Pièce DéfectueuseRemarques FR30 FR31

82053, DH212 specifications

The Shindaiwa 82053, DH212 is a powerful and versatile tool designed for professionals in the landscaping and horticultural industries. Known for its robust performance and reliability, this product stands out among its peers due to several innovative features and technologies tailored to meet the needs of demanding users.

One of the main highlights of the Shindaiwa 82053 is its powerful engine. This tool is equipped with a high-performance engine that delivers exceptional cutting power while maintaining fuel efficiency. The engine's design minimizes vibration and ensures smooth operation, allowing users to work effectively without excessive fatigue.

The DH212, a key component of the Shindaiwa 82053, is recognized for its ergonomic design. This feature enhances user comfort during extended periods of operation. The handles are thoughtfully designed to provide superior grip and control, reducing the strain on the operator's hands and arms. This is particularly important for professionals who often work long hours.

Another significant characteristic of the Shindaiwa 82053 is its advanced cutting technology. The dual-edge blade system provides a cleaner and faster cut, allowing for efficient trimming of hedges and bushes. The blades are crafted from high-quality materials that ensure durability and longevity, even under heavy use.

The tool's rapid-start feature is designed to reduce startup time, enabling users to get to work quickly without unnecessary delays. Additionally, the advanced air filtration system helps to keep the engine clean, extending its lifespan and improving reliability.

The Shindaiwa 82053, DH212 is also known for its easy maintenance. The design incorporates accessible components, allowing users to perform routine checks and repairs with minimal hassle. This user-friendly approach reduces downtime and enhances productivity.

In terms of safety, the Shindaiwa 82053 features multiple safeguards that protect the user during operation. The protective guards and blade covers ensure that operators can work confidently without the fear of accidental injuries.

Overall, the Shindaiwa 82053, DH212 embodies a perfect blend of power, comfort, and advanced technology, making it an ideal choice for professional landscapers and gardeners. Its exceptional performance and reliability are sure to make it a trusted tool in any landscaping arsenal. Whether trimming hedges or maintaining gardens, the Shindaiwa 82053 is a dependable ally that ensures work is completed efficiently and effectively.
Top Page Image Contents