Shindaiwa P231 General Maintenance, Daily Maintenance, Hour Maintenance, Muffler, Spark Plug

Page 15

General Maintenance

IMPOERTANT!

MAINTENANCE, REPLACEMENT, OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEM MAY BE PERFORMED BY ANY REPAIR ESTAB- LISHMENT OR INDIVIDUAL. HOW- EVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA KOGYO, LTD. AND USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURA- BILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUT- COME OF THE WARRANTY CLAIM.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped.

Disconnect the spark plug wire before performing service or maintenance.

WARNING!

Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.

Muffler

WARNING!

Operating the engine without a muffler or with a muffler that is damaged or improperly installed can increase engine noise suf- ficiently to cause hearing loss.

This unit must never be operated with a faulty or missing muffler. Make sure the muffler is well secured and in good condi- tion. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Daily Maintenance

Prior to each work day, perform the following:

■Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.

Keep cooling

fins clean.

Keep air

passages

clean.

10-Hour Maintenance

Every 10 hours of operation (more frequently in dusty or dirty conditions):

■Remove the air cleaner element from the air cleaner housing and clean it thoroughly with soap and water. Let it dry before reinstalling the element.

CAUTION!

Do not operate the unit if the air cleaner or element is damaged, or if the element is wet.

WARNING!

Always wear gloves when working around the cutter assembly.

■Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.

■Clean any debris or dirt from the cutting attachment. Check the bar and chain for damage or incorrect adjustment.

■Check for loose or missing screws or components. Make sure the cutter attachment is securely fastened.

Loosen Knob

■Check the entire unit for leaking fuel or grease.

■Make sure nuts, bolts, and screws (except carburetor idle speed adjusting screws) are tight.

Remove and clean the

element.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Español SP1 Français FR1 P231 Pole PrunerIntroduction ContentsBeware of pinching Safety PrecautionsKickback and Pinching Beware of KickbackOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels 2804 mm/110.4 Slide switchAdjustable oiler Kg/13.4 lbConnecting the Throttle Cable AssemblyPrior to assembly Powerhead InstallationAssembling tube sections Adjusting the Throttle CableKeep the open ends of the tubes clean and free of debris Connect The Throttle CableInstalling and Adjusting the Bar and Chain Installing the ChainDisassembling the tube sections Chain Oiler Adjusting the ChainAdjusting Oil Flow Rate Adjust the pump as followsAlways transport and store fuels in an approved container Mixing FuelFilling the Fuel Tank Minimize the risk of fire, burns, and personal injuryNever start the engine from the operating position Slide the ignition switch to the on positionWhen the Engine Starts Starting the EngineAdjusting the Engine Idle Check and Adjust Idle SpeedStopping the Engine Using the Pole Pruner Muffler General MaintenanceDaily Maintenance Hour Maintenance10/15-Hour Maintenance Clean or replace fuel filterEvery 10 to 15 hours of operation Long Term Storage MaintenanceMuffler maintenance Every 135 hours of operation, remove and clean the mufflerFor consistent filing angles, use a filing guide Sharpening the ChainTroubleshooting Guide Chain rotates at idle speed Poor accelerationEngine stops abruptly Engine difficult to shut offThis Warranty is Administered by Fax Specifications subject to change without notice P231 Podadora de Extensión Índice Introducción Declaraciones de seguridadGuardarte de contragolpe Instrucciones generales de seguridadTrabaje con cuidado ¡ADVERTENCIA! Contragolpe y aprieteEl operario debidamente equipado Instrucciones de seguridadPrecauciones del funcionamiento Instrucciones de seguridad continuación Etiquetas de seguridadRealice siempre el mantenimiento Especificaciones Descripción del productoConexión del cable del acelerador EnsamblarAntes de Ensamblar Barras y cadenas opcionalesEnsamblar de las secciones del tubo Ensamblar continuaciónConecte el cable del acelerador Ajuste el cable del aceleradorPiñón Instalación y ajuste de la barra y la cadena de la sierraDesmontaje de las secciones del tubo Instalación la cadenaAjuste del flujo del aceite Adjuste la cadenaBomba de aceite Llenado del depósito de aceite100 200 400 Mezcla de combustibleLlenando el tanque de combustible Ejemplos de cantidades de mezcla a proporción deArranque del motor Nunca arranque el motor desde la posición de operaciónCuando arranca el motor… Continuar girando cuando se para El motor Parada del motorAjuste de marcha mínima del motor El accesorio de cortes pudoEl uso de la potadora de extensión Mantenimiento general Mantenimiento diarioCada 10 horas mantenimiento Mantenimiento continuación Cada 10 15 horas mantenimientoCada 50 horas mantenimiento Almacenamiento de largo plazo Mantenimiento del silenciadorCada 135 horas de operación, retire y limpie el silenciador Rendimiento de la cadena Para limar en ángulos iguales, use unaGuía para la lima Remedio Guía de localización de fallasQué revisar Posible causaQué revisar Posible causa Remedio Guía de localización de fallas continuaciónEsta Garantía ES Administrada POR Notas Tronçonneuse à perche P231 De ce produit contiennent des sub Introduction Mises en gardeUnénoncéprécédédelamention Les échappements du moteurRéaliser les coupes à haut régime Consignes de sécuritéÉquipement complet de l’utilisateur Consignes d’utilisationNe pas utiliser l’appareil sans le silencieux Étiquettes et dispositifs de sécurité Consignes d’utilisation suiteCaractéristiques techniques Raccord du câble d’accélération Avant l’assemblageMontage de la tête motorisée Options du guide-chaîne et de la chaîneAssemblage les éléments du tube Assemblage suiteRaccorder le câble d’accélération Réglage du câble d’accélérationInstallation et réglage du guide-chaîne et de la chaîne Installation de la chaîneDésassemblage des éléments Réglage du débit d’huile Réglage de la chaîneHuileur de chaîne Remplissage du réservoir d’huileRemplissage du réservoir de carburant Mélange de carburantLorsque le moteur démarre Démarrage du moteurArrêt du moteur Réglage du ralenti du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Silencieux EntretienEntretien quotidien Entretien aux 10 heuresEntretien aux 50 heures Entretien suiteRemisage à long terme Entretien aux 10 à 15 heuresEntretien du pare-étincelles Technique d’affûtage correcte Affûtage de la chaînePoints à contrôler SolutionPoints à contrôler Cause probable Solution Guide de dépannageCause probable Guide de dépannage suiteÉtendue DE LA Garantie DU Fabricant FR22 FR23 FR24

P231, 62888-94013 specifications

Shindaiwa has long been recognized for its commitment to quality in outdoor power equipment, and the model 62888-94013, specifically the P231, is no exception. This efficient and robust handheld blower is designed for both professionals and homeowners who demand reliable performance for leaf and debris management.

One of the standout features of the Shindaiwa P231 is its impressive air velocity. With a maximum air speed of 175 mph, this blower can tackle even the most stubborn leaves and debris with ease. This powerful airflow is complemented by a lightweight design, making it easy to maneuver even during extended use. Weighing just around 9.8 lbs, the P231 minimizes operator fatigue, allowing for longer periods of operation without discomfort.

Powering the P231 is a reliable 23.9 cc two-stroke engine, engineered for efficient fuel consumption and reduced emissions. This engine technology not only adheres to environmental standards but also provides a perfect balance of power and efficiency. The use of Shindaiwa’s proprietary engine design ensures that the blower can perform consistently regardless of the conditions, whether it’s wet leaves in the fall or light debris in the spring.

Another noteworthy feature of the P231 is its durable construction. Built with high-quality materials, the blower is designed to withstand the rigors of frequent use. The ergonomic handle is designed for comfort, ensuring a secure grip that reduces vibration and enhances control during operation. Furthermore, the blower includes a user-friendly start system that makes kick-starting the engine a hassle-free experience.

Shindaiwa also prioritizes ease of maintenance in the P231 model. It is equipped with a simple air filter access and a fuel tank designed for easy refueling. This attention to user-friendliness ensures that you can keep your equipment in top condition with minimal effort.

In summary, the Shindaiwa 62888-94013 P231 is a dynamic handheld blower that combines power, efficiency, and durability. Ideal for both professional landscapers and homeowners, its features like high air velocity, quality engine technology, lightweight design, and ease of maintenance make it an excellent choice for effective outdoor cleanup. Whether it’s for a large property or routine yard work, the P231 delivers reliability and outstanding performance every time.
Top Page Image Contents