Servis-Rhino P/N 00763618C manual Belt Adjustment Procedure All Models except

Page 107

MAINTENANCE

1

2 4

3

5

FIGURE 10

3/4"

10 LBS.

Locknut

Flatwasher

Spacer

FlatwasherBolt

BELT ADJUSTMENT PROCEDURE (All Models except 11')

Adjust the tension in the drive belt, item1, properly so that it deflects 3/4" when a force of approximately 10 lb. is applied as indicated.

Tighten drive belt by loosening nut, items 2 & 5, and turn nut, item 3 against the anchor plate until proper tension is reached. DO NOT OVERTIGHTEN. Tighten jam nut, item 4., and nut item 2. And retighten item 5. FIGURE 10.

Replace the belt safety shields using wing nuts.

BELT INSTALLATION (All Model except 11')

To replace drive belt (1), remove belt shields and loosen nuts (2, and 3). Loosen and remove nut (5). Disassemble tensioning idler noting location of all loose parts.Loosen front pair of gearbox mount retaining bolts. Remove rear gearbox mount retaining bolts. Note location of shim washers if present so they can be reinstalled later. This allows gearbox mount to be raised so belt can be inserted and removed between top of deck and gearbox shaft. Once belt is in place on large drive sheave, reinstall and tighten gearbox retaining hardware. Locate rear of gearbox mount at same elevation as it was, before being removed. Reassemble tensioning idler with belt between idler and bracket. Route belt as shown in layout and set tension per adjustment procedure.

Turf Flex 08-01	Maintenance Section 5-7
	Maintenance Section 5-7
© 2004 Alamo Group Inc.

MAINTENANCE

Image 107

Contents Turf Flex To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Instructivo Peligro¡LEA EL Safety Safety Following rules Serious injury or death. SG-26 Safety With the windows closed. SGM-11 Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life See Your SERVIS-RHINO Dealer Parts Information12 3A 3536 Peligro QTY Level DescriptionSafety D103 Turf Flex 08/01 Safety Section 04-23-99 00763535 Turf Flex Name D102 Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Dealer SET-UP Instructions AssemblySwivel and Lift ARM Attachment Wing Mower Attachment Hydraulic Cylinder AttachmentCaster Wheel Attachments Rear Mower Figure Caster Wheel Attachments Rear Mower 11 Model Caster Wheel Attachments Wing Mower FigureRear Mower Attachment Caster Wheel Attachments Wing Mower 11 Model FigureAxle Arms in Postion Assembly SMV Attachment Driveshaft AttachmentHydraulic Hose Attachment Spool ValveLeft Wing Driveline Right Wing Driveline Wing Driveshaft AttachmentRope Routing for Automatic Head Locks Assembly Page Operation Section Attaching Cutter to Tractor Tractor PreparationSafety Chains Pull Type Driveline Attachment to Tractor Cutting Height AdjustmentRoller Adjustment Mowing Tips Starting & Stopping MowerCutting Speed Before Operating or Transporting this Mower Driveline Length Check ProcedureSpecial Instructions for Rough Terrain Operations Transporting Cutter DEG CV Driveline Check ProceduresStreaking Problem Possible Cause RemedyFrayed Edges on Page Maintenance Section Lubrication Information MaintenanceCenter 4-WAY Gear BOX GearboxBlade Spindle Lubrication Swivel AssemblyGauge Wheel Assemblies Wing Driveline Profile Lubrication Driveline LubricationCV Driveline Profile Lubrication Blade Removal Blade InstallationBlade Servicing Blade SharpeningBelt Adjustment Procedure All Models except Belt Installation 11 Model Belt Adjustment Procedure 11 ModelProper Torque for Fasteners StorageMaintenance Tool Turf Flex Maintenance Section 12-13-95 Page To the OWNER/OPERATOR/DEALER TURFFLEX-OMWPL-08/01