Servis-Rhino P/N 00763618C manual Belt Adjustment Procedure 11 Model, Belt Installation 11 Model

Page 108

MAINTENANCE

MAINTENANCE

BELT ADJUSTMENT PROCEDURE (11' MODEL)

Adjust the tension in the drive belt, item 1, properly so that they deflect 3/4" when a force of approximately 10 lb. is applied.

Tighten drive belt by loosening one nut, items 2, and tightening other nut until belt is properly tensioned. Jam the first Nut to hold adjustment. NOTE: If more thread adjustment is needed loosen off and hook Spring (4) in next shorter Chain Link (3).

Replace the belt safety shields using wing nuts.

BELT INSTALLATION (11' MODEL)

To replace drive belt (1), remove belt shields and loosen nuts (2). Loosen the nut (2). Disassemble tensioning Spring noting location of all loose parts.Loosen front pair of gearbox mount retaining bolts. Remove rear gearbox mount retaining bolts. Note location of shim washers if present so they can be reinstalled later. This allows gearbox mount to be raised so belt can be inserted and removed between top of deck and gearbox shaft. Once belt is in place on large drive sheave reinstall and tighten gearbox retaining hardware. Locate rear of gearbox mount at same elevation as it was, before being removed. Reassemble tensioning Spring with Chain. Route belt as shown in layout and set tension per adjustment procedure.

1

2

4

3

	FIGURE 11
Turf Flex 08-01	Maintenance Section 5-8	R 12-13-95
	Maintenance Section 5-8	R 12-13-95

© 2004 Alamo Group Inc.

Image 108

Contents Turf Flex To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Peligro ¡LEA ELInstructivo Safety Safety Following rules Serious injury or death. SG-26 Safety With the windows closed. SGM-11 Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information See Your SERVIS-RHINO Dealer12 3A 3536 QTY Level Description PeligroSafety D103 Turf Flex 08/01 Safety Section 04-23-99 00763535 Turf Flex Name D102 Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Assembly Dealer SET-UP InstructionsSwivel and Lift ARM Attachment Hydraulic Cylinder Attachment Wing Mower AttachmentCaster Wheel Attachments Rear Mower Figure Caster Wheel Attachments Wing Mower Figure Caster Wheel Attachments Rear Mower 11 ModelCaster Wheel Attachments Wing Mower 11 Model Figure Rear Mower AttachmentAxle Arms in Postion Assembly Driveshaft Attachment Hydraulic Hose AttachmentSpool Valve SMV AttachmentWing Driveshaft Attachment Left Wing Driveline Right Wing DrivelineRope Routing for Automatic Head Locks Assembly Page Operation Section Tractor Preparation Attaching Cutter to TractorSafety Chains Pull Type Cutting Height Adjustment Roller AdjustmentDriveline Attachment to Tractor Starting & Stopping Mower Cutting SpeedMowing Tips Driveline Length Check Procedure Before Operating or Transporting this MowerSpecial Instructions for Rough Terrain Operations Transporting Cutter CV Driveline Check Procedures DEGProblem Possible Cause Remedy StreakingFrayed Edges on Page Maintenance Section Maintenance Lubrication InformationGearbox Center 4-WAY Gear BOXSwivel Assembly Gauge Wheel AssembliesBlade Spindle Lubrication Driveline Lubrication CV Driveline Profile LubricationWing Driveline Profile Lubrication Blade Installation Blade ServicingBlade Sharpening Blade RemovalBelt Adjustment Procedure All Models except Belt Adjustment Procedure 11 Model Belt Installation 11 ModelStorage Proper Torque for FastenersMaintenance Tool Turf Flex Maintenance Section 12-13-95 Page To the OWNER/OPERATOR/DEALER TURFFLEX-OMWPL-08/01