Servis-Rhino P/N 00763618C manual Maintenance

Page 110

MAINTENANCE

MAINTENANCE

BLADE SPINDLE SERVICE INSTRUCTIONS (FIGURE 13)

DISASSEMBLY

1.Remove adjusting nut #3.

2.Support spindle housing #2 under flange and drive out shaft assembly #1.

CAUTION! Use tube on top end of shaft to protect grease fitting.

3.Remove bearing cups from housing. Remove lower bearing from shaft assembly by inserting punch through hole in shaft hub and drive bearing off shaft. Once bearing has been moved 3/8" - 1/2" up shaft, lay flat bars on either side of the shaft and support across vice..or other convenient means. Remove bearing by driving as described in step #2.

4.Clean all parts and reassemble with new parts can proceed.

ASSEMBLY

1.Press bearing cups in spindle housing.

2.Insert bearing cone in bottom of housing and press in bottom seal #6, flush with bottom of housing.

3.Insert shaft assembly #1 through bottom seal and bearing. Press or lightly drive shaft until it bottom against bearing.

4.Turn spindle over and sit on blade mount washer. Install top bearing and seal. NOTE: Direction of seal lip on top side.

5.Install top adjusting nut #3. Adjust nut to give bearing end play of .002" - .006". Apply Loctite 242 to nut.

6.Grease spindle, until grease is forced out top seal lip.

8

7

4

 

 

 

 

3

Use a 15/16" mini-

 

mum I.D. Tube to

2

remove Shaft.

 

5

4

FIGURE 13

 

6

1

 

 

 

 

 

Turf Flex 08-01

Maintenance Section

5-10

R 12-13-95

 

© 2004 Alamo Group Inc.

Image 110
Contents Turf Flex To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Instructivo Peligro¡LEA EL Safety Safety Following rules Serious injury or death. SG-26 Safety With the windows closed. SGM-11 Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information See Your SERVIS-RHINO Dealer12 3A 3536 QTY Level Description PeligroSafety D103 Turf Flex 08/01 Safety Section 04-23-99 00763535 Turf Flex Name D102 Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Assembly Dealer SET-UP InstructionsSwivel and Lift ARM Attachment Hydraulic Cylinder Attachment Wing Mower AttachmentCaster Wheel Attachments Rear Mower Figure Caster Wheel Attachments Wing Mower Figure Caster Wheel Attachments Rear Mower 11 ModelCaster Wheel Attachments Wing Mower 11 Model Figure Rear Mower AttachmentAxle Arms in Postion Assembly Spool Valve Driveshaft AttachmentHydraulic Hose Attachment SMV AttachmentWing Driveshaft Attachment Left Wing Driveline Right Wing DrivelineRope Routing for Automatic Head Locks Assembly Page Operation Section Tractor Preparation Attaching Cutter to TractorSafety Chains Pull Type Driveline Attachment to Tractor Cutting Height AdjustmentRoller Adjustment Mowing Tips Starting & Stopping MowerCutting Speed Driveline Length Check Procedure Before Operating or Transporting this MowerSpecial Instructions for Rough Terrain Operations Transporting Cutter CV Driveline Check Procedures DEGProblem Possible Cause Remedy StreakingFrayed Edges on Page Maintenance Section Maintenance Lubrication InformationGearbox Center 4-WAY Gear BOXBlade Spindle Lubrication Swivel AssemblyGauge Wheel Assemblies Wing Driveline Profile Lubrication Driveline LubricationCV Driveline Profile Lubrication Blade Sharpening Blade InstallationBlade Servicing Blade RemovalBelt Adjustment Procedure All Models except Belt Adjustment Procedure 11 Model Belt Installation 11 ModelStorage Proper Torque for FastenersMaintenance Tool Turf Flex Maintenance Section 12-13-95 Page To the OWNER/OPERATOR/DEALER TURFFLEX-OMWPL-08/01