Servis-Rhino P/N 00763618C manual Driveline Attachment to Tractor, Cutting Height Adjustment

Page 92

OPERATION

OPERATION

DRIVELINE ATTACHMENT TO TRACTOR

1.Grasp and pull collar on end of attaching yoke toward mower.

2.Slide yoke (with collar depressed) onto PTO shaft.

3.Move yoke back and forth until locking collar clicks forward and locks the yoke in place.

WARNING! When attaching PTO yoke to tractor PTO shaft, it is important that spring activated locking collar slides freely and is seated in groove on PTO shaft.

WARNING! Be sure PTO shielding and all other shielding is installed and is in good condition.

WARNING! Avoid personal injury! Be sure tractor engine is off, key is removed, and ALLOW BLADES TO STOP TURNING before dismounting to make adjustments.

CUTTING HEIGHT ADJUSTMENT

IMPORTANT: When operating, remote valve lever must be in detent position to allow mower heads to follow ground contour. (Float)

IMPORTANT: Avoid very low cutting heights. Striking the ground with blades gives the most damaging shock loads a cutter can encounter and will cause damage to cutter and drive system.

1.Using the tractor hydraulics, raise the mowers off the ground and support under it with secure blocking so not to let the mower drift down during maintenance.

2.Holding wheel and yoke assembly up, remove quick-lock pin from top of gauge wheel spindle. Position full length spacers and 1/4" spacer as required. All spacers on top of spindle tube allows for approximately 1/2" cutting height. Adjustments range from 1/2" to a maximum of 5" in 1/4" increments. Figure 4.

3.For the 11' Model Shaft Height Adjustment remove quick-lock Pin from top of Shaft. Remove Shaft from Axle Arm. Position full length Spacers and half Spacers as required. All spacers on top of spindle tube allows for approximately 1/2" cutting height. Adjustments range from 1/2" to a maximum of 5" in 1/4" increments. Figure

Add spacers for cutting height adjustment. One, 1" Spacer gives approximately 1-1/2" cutting height.

Figure 4

Figure 5

ROLLER ADJUSTMENT

 

Place roller brackets in lowest position for cutting heights 5" to approximately 3". Place in highest position for 1" to approximately 1-1/2" cutting heights. Place in intermediate position for cutting heights of 2" to approximately 3".

Turf Flex 08-01

Operation Section 4-4

R 12-13-95

© 2004 Alamo Group Inc.

 

 

Page 91 Page 93
Image 92
Page 91 Page 93
Contents Turf Flex To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Instructivo Peligro¡LEA EL Safety Safety Following rules Serious injury or death. SG-26 Safety With the windows closed. SGM-11 Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information See Your SERVIS-RHINO Dealer12 3A 3536 QTY Level Description PeligroSafety D103 Turf Flex 08/01 Safety Section 04-23-99 00763535 Turf Flex Name D102 Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Assembly Dealer SET-UP InstructionsSwivel and Lift ARM Attachment Hydraulic Cylinder Attachment Wing Mower AttachmentCaster Wheel Attachments Rear Mower Figure Caster Wheel Attachments Wing Mower Figure Caster Wheel Attachments Rear Mower 11 ModelCaster Wheel Attachments Wing Mower 11 Model Figure Rear Mower AttachmentAxle Arms in Postion Assembly Driveshaft Attachment Hydraulic Hose AttachmentSpool Valve SMV AttachmentWing Driveshaft Attachment Left Wing Driveline Right Wing DrivelineRope Routing for Automatic Head Locks Assembly Page Operation Section Tractor Preparation Attaching Cutter to TractorSafety Chains Pull Type Driveline Attachment to Tractor Cutting Height AdjustmentRoller Adjustment Mowing Tips Starting & Stopping MowerCutting Speed Driveline Length Check Procedure Before Operating or Transporting this MowerSpecial Instructions for Rough Terrain Operations Transporting Cutter CV Driveline Check Procedures DEGProblem Possible Cause Remedy StreakingFrayed Edges on Page Maintenance Section Maintenance Lubrication InformationGearbox Center 4-WAY Gear BOXBlade Spindle Lubrication Swivel AssemblyGauge Wheel Assemblies Wing Driveline Profile Lubrication Driveline LubricationCV Driveline Profile Lubrication Blade Installation Blade ServicingBlade Sharpening Blade RemovalBelt Adjustment Procedure All Models except Belt Adjustment Procedure 11 Model Belt Installation 11 ModelStorage Proper Torque for FastenersMaintenance Tool Turf Flex Maintenance Section 12-13-95 Page To the OWNER/OPERATOR/DEALER TURFFLEX-OMWPL-08/01
Top Page Image Contents