Servis-Rhino P/N 00763618C manual Following rules

Page 11
(SG-19)
(SG-21)

SAFETY

WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.

WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is off before working on the Implement.

(SG-20)

WARNING! Transport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the safe transport speeds for you and the equipment. Make sure you abide by the

following rules:

1.Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement.

As you increase the speed of the Tractor the stopping distance increases. Determine the maximum safe transport speed for you and this Equipment.

2.Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that it is safe to operate at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum safe turning speed for you and this equipment before operating on roads or uneven ground.

3.Only transport the Tractor and Implement at the speeds that you have determined are safe and which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you andwatch out for the other guy.

WARNING! Always read carefully and comply fully with the manufacturers instructions when handling oil, solvents, cleansers, and any other chemical agent.(SG-22)

Turf Flex 08/01

Safety Section 1-5

© 2004 Alamo Group Inc.

 

SAFETY

Image 11
Contents Turf Flex To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Instructivo Peligro¡LEA EL Safety Safety Following rules Serious injury or death. SG-26 Safety With the windows closed. SGM-11 Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life See Your SERVIS-RHINO Dealer Parts Information12 3A 3536 Peligro QTY Level DescriptionSafety D103 Turf Flex 08/01 Safety Section 04-23-99 00763535 Turf Flex Name D102 Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Dealer SET-UP Instructions AssemblySwivel and Lift ARM Attachment Wing Mower Attachment Hydraulic Cylinder AttachmentCaster Wheel Attachments Rear Mower Figure Caster Wheel Attachments Rear Mower 11 Model Caster Wheel Attachments Wing Mower FigureRear Mower Attachment Caster Wheel Attachments Wing Mower 11 Model FigureAxle Arms in Postion Assembly SMV Attachment Driveshaft AttachmentHydraulic Hose Attachment Spool ValveLeft Wing Driveline Right Wing Driveline Wing Driveshaft AttachmentRope Routing for Automatic Head Locks Assembly Page Operation Section Attaching Cutter to Tractor Tractor PreparationSafety Chains Pull Type Driveline Attachment to Tractor Cutting Height AdjustmentRoller Adjustment Mowing Tips Starting & Stopping MowerCutting Speed Before Operating or Transporting this Mower Driveline Length Check ProcedureSpecial Instructions for Rough Terrain Operations Transporting Cutter DEG CV Driveline Check ProceduresStreaking Problem Possible Cause RemedyFrayed Edges on Page Maintenance Section Lubrication Information MaintenanceCenter 4-WAY Gear BOX GearboxBlade Spindle Lubrication Swivel AssemblyGauge Wheel Assemblies Wing Driveline Profile Lubrication Driveline LubricationCV Driveline Profile Lubrication Blade Removal Blade InstallationBlade Servicing Blade SharpeningBelt Adjustment Procedure All Models except Belt Installation 11 Model Belt Adjustment Procedure 11 ModelProper Torque for Fasteners StorageMaintenance Tool Turf Flex Maintenance Section 12-13-95 Page To the OWNER/OPERATOR/DEALER TURFFLEX-OMWPL-08/01